SoundCraft Vi5000 страница 145 Скачать руководство пользователя

Страница: 145 / 225

Vi5000/7000 User Manual

15.2: OSCILLATOR SETUP

15.2: OSCILLATOR SETUP

OSCILLATOR > SETUP

Oscillator To Talkback

Route the oscillator signal to the TB Bus (replaces the TB signal).

Oscillator Frequency

Adjust the Oscillator sine wave Frequency in the range 20Hz to 20kHz.

Oscillator Bus Assignment

Used in conjunction with the Oscillator to Bus touch screen switch.

Opens an output assignment page where you can select any of the 32 group busses or the Mix L, R, and C out-
puts.

Oscillator On

Activate the console's oscillator.

Oscillator Gain

Adjust the oscillator output level

Oscillator Output

Assign the oscillator to individual physical outputs.

Opens an output assignment page with all available physical outputs available.

Содержание Vi5000


































































































































































































































Результаты поиска

Содержание Vi5000

Отзывы:

Похожие инструкции для Vi5000

Бренды по названию

Популярные бренды

SoundCraft Vi5000, Руководство пользователя

Результаты поиска

Содержание Vi5000

Отзывы:

Похожие инструкции для Vi5000

Бренды по названию

Популярные бренды