SoundCraft Vi5000 страница 104 Скачать руководство пользователя

Страница: 104 / 225

Vi5000/7000 User Manual

11.0: SOLO SYSTEM

11.0: SOLO SYSTEM

SOLO SYSTEM BEHAVIOR

AFL, PFL and SIP

The solo system on the console comprises a non-destructive (solo bus routing only) PFL

and AFL Solo capability for Inputs and Outputs, and also the option of a ‘destructive’

Solo-In-Place (SIP) mode (channel muting solo), for use only during sound-checks or

rehearsals. Solo-In-Place mode has to be enabled from within the Monitor Setup and

changes the mode of operation of the Solo System. It is automatically cancelled if the

Monitor Setup screen is closed, to ensure that it cannot be left on accidentally.

PFL and AFL Soloing (SIP Mode OFF)

• Soloing a single Input locally generates a PFL or AFL Solo onto the Solo Bus, depend-

ing on the mode selected in the Monitor Setup page (default is AUTO, see next point).

• If the Input Solo Mode is set to AUTO in the Monitor Setup page, soloing more than one

Input locally (by pressing and holding the first Solo/Sel switch then pressing others, or

switching off AUTO CANCEL mode) will generate an AFL Solo onto the Solo Bus from all

soloed Inputs. If a single output is soloed, the solo will be PFL.

• The PFL feed from Mono Inputs is taken after the channel Pan control so the signal

heard on the Monitor outs will reflect the Pan setting. If the Input is a Stereo Input, the

PFL feed is left channel to left Solo Bus, right to right.

• The AFL feed from Mono or stereo (paired) Inputs is stereo and follows the channel

Pan.

• Soloing an Output (either locally or via a VCA Master Solo) generates an AFL or PFL

Solo, depending on the mode selected in Monitor Setup (default is AFL for outputs).

The post-fade Output signal is switched onto the Solo Bus.

• In all cases when SIP Mode is OFF, operation of any Solo will switch the audio onto the

Solo Bus and the Monitor section will be automatically switched so that the Solo audio

replaces the previous monitor source selection (if any) assuming that IN Solo and/or OUT

Solo have been selected as a Monitor Source in the Monitor Setup Page.

Solo-In-Place Soloing (SIP mode ON)

• Soloing an Input generates a ‘destructive’ SIP Solo, actually muting or dimming all other

Inputs which are not Soloed or set to Mute Safe, as if you had pressed their channel ON

switches. This has the effect of soloing on the main outputs. Other channels which are

subsequently soloed will be unmuted. The amount of dimming is controlled by the SOLO

BLEND control on the front panel.

• Soloing an Input (or group of Inputs) by soloing a VCA Master that the input is assigned

to, generates a SIP Solo on all Inputs in the VCA Group.

* The Input signal is not switched onto the Solo Bus, and the Monitor section does not

switch the Solo Bus audio to override the monitor source selection (you hear the soloed

signal(s) via the Master LRC busses directly.

• Soloing an Output generates a normal Output AFL or PFL Solo (according to the mode

selection made in Monitor Setup), the same as if SIP Mode was OFF. The Output signal

is switched onto the Solo Bus and the Monitor section switches so that the Output. So-

loed audio is heard on the Monitors, replacing the previous monitor source, if any.

Solo management in the
Monitors SETUP screen
- [SETUP] button above
MNTR A/B fader.

Содержание Vi5000


































































































































































































































Результаты поиска

Содержание Vi5000

Отзывы:

Похожие инструкции для Vi5000

Бренды по названию

Популярные бренды

SoundCraft Vi5000, Руководство пользователя

Результаты поиска

Содержание Vi5000

Отзывы:

Похожие инструкции для Vi5000

Бренды по названию

Популярные бренды