Sottoriva SVP08-0 Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 79

background image

Rev. F
dated 02/07/2015

SVP08-0/1/2/3 - Code: 3529.0231.01

38

Service

Phone (+39) 0445.595.111

PT

0715

MV

0715

MC

0715

Arc. 66-VI

6.3

Checks before start-up

1) make sure all fixed guards are in place;
2) make sure that all safety equipment is in place and operational: mobile guard

microswitches

ref. 1 and 11 Fig. 4

on page 23, safety ring microswitch

ref. 13

Fig. 4

and mushroom-head button

(ref. 2 Fig. 11

on page 40

)

for the emergency stop.

3) make sure that the master power switch

(ref. 1 Fig. 10

on page 39

)

and power

socket are in place and operational.

6.4

Correct use of the machine

The machine considered in this Manual is suited to the processing of food under
current law at the time at which it was shipped by the Manufacturer; this suitability
depends over time on careful cleaning, at least daily, and on regular service and
inspection, including immediate replacement of any parts in contact with foodstuffs
(dough, flour, water, etc.) which may be damaged, worn or no longer suited to the
hygienic treatment of foodstuffs.

6.5

Improper use

The following prohibitions do not cover all possible incorrect uses of the machine,
but relate only to reasonably probable ones.

6.6

Operational limits

The total mass of dough to be divided may not exceed the nominal capacity of the
hopper given in

Table 1 on page 25

.

Operator

Before

starting the machine, proceed as follows:

Prohibition!

- It will be dangerous for the mechanical functioning of the machine and

for the operator to use the machine for aims different from the aims
stated on page 23, par. 4.1. The manufacturer can not be considered
responsible for an incorrect use and /or for an use not complying with
the instructions stated in this manual, unless otherwise stated.

- Do not run the machine at any speed other than that set by the Manufac-

turer. Obtain the Manufacturer’s permission before modifying the speed
settings.

- During processing, it is strictly prohibited to access the hopper using

steps or similar supports in order to push the dough down into the
machine, either using the hands or any other tool.

«
...
38
39
40
41
42
...
»

Содержание SVP08-0
















































































Отзывы:

Нет отзывов

Похожие инструкции для SVP08-0

Бренд: Panasonic Страницы: 9

Бренд: 3A HEALTH CARE Страницы: 16

Бренд: idiag Страницы: 10

Бренд: Bandit Страницы: 136

Versaflo S Series

Бренд: 3M Страницы: 11

DBI Sala EXOFIT

Бренд: 3M Страницы: 32

Бренд: 3M Страницы: 8

Бренд: Accurate Bio-Medical Technology Страницы: 35

Бренд: KaVo Страницы: 4

ORTHOPANTOMOGRAPH OP 3D

Бренд: KaVo Страницы: 40

KEY Laser III 1243

Бренд: KaVo Страницы: 103

EXTRAmatic 9040

Бренд: KaVo Страницы: 56

ESTETICA E70 Vision

Бренд: KaVo Страницы: 48

Бренд: Kaya Safety Страницы: 5

Бренд: Kawai Страницы: 166

Бренд: Land Pride Страницы: 32

Бренд: Mackworth Страницы: 38

Бренд: P&P Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды