Sottoriva SVP08-0 Скачать руководство пользователя страница 52 | Manualshive

Страница: 52 / 79

background image

Rev. F
dated 02/07/2015

SVP08-0/1/2/3 - Code: 3529.0231.01

50

Service

Phone (+39) 0445.595.111

PT

0715

MV

0715

MC

0715

Arc. 66-VII

7.4.1.2 Replacing the drive belt (ref. 2 Fig. 14 on page 55)

1) Remove the guards;
2) set the machine to its minimum speed of production, using the handwheel

(

ref. 5

Fig. 4

on page 23);

3) turn off the machine, while moving the general switch to the 0 position (

ref. 1

Fig. 10

on page 39);

4) disconnect the plug from the electrical connector;
5) remove the chain (

ref. 9

Fig. 14

);

6) using one hand, grip the belt which is stretched between the two pulleys (

ref. 4

and

7

Fig. 14

);

7) using the other hand, turn the handwheel (

ref. 5

Fig. 4

) until the belt can be

extracted;

8) fit the new belt by first forcing it into the groove of the variable pulley (

ref. 7

Fig. 14

) so that it is stretched as taut as possible;

9) setting the handwheel (

ref. 5

Fig. 4

) to minimum production speed;

10) fit it around the driven pulley (

ref. 4

Fig. 14

);

11) refit the chain (

ref. 9

Fig. 14

);

12) refit the side guards, securing them using the respective fixing screws.

7.4.1.3 Replacing the outfeed conveyor drive belt (ref. 6 Fig. 14)

1) Remove the side guards;
2) Raise the motor base (

ref. 8

Fig. 14

) until the belt can be extracted from the

pulley groove;

3) keeping the base raised, fit the new belt;
4) refit the side guards, securing them with the relative fixing screws.

7.4.1.4 Replacing the outfeed conveyor belt (ref. 3 Fig. 4)

1) Remove the side guards;
2) slacken the conveyor belt as much as possible;
3) remove the plastic guard from the conveyor frame inside the machine outfeed

opening;

4) through the holes of the pulley (

ref. 3

Fig. 14

), remove the locking screws of the

cap located behind it;

5) remove the Seeger ring which secures the shaft (

ref. 5

Fig. 14

);

6) remove the two fixing screws of the conveyor belt support sheet from the back

of the machine;

7) gently pull the conveyor assembly towards the outfeed so as to free the support

sheet from the necks of the roller;

8) pull the pulley towards you (

ref. 4

Fig. 14

), after having tapped on the neck of

the roller with a metal prop (

ref. 5

Fig. 14

), and fully extract the roller;

9) fully extract the conveyor belt assembly;
10) replace the conveyor belt;
11) reinsert the entire assembly until it is possible to fit the roller which was

previously extracted from the conveyor belt;

12) refit the Seeger ring;

Warning!

Once the belt is removed, the motor will be unsupported. Do not let the
base drop suddenly, but hold it in position or lower it gently downwards
using your hand.

«
...
50
51
52
53
54
...
»

Содержание SVP08-0
















































































Отзывы:

Нет отзывов

Похожие инструкции для SVP08-0

Бренд: FASTERHOLT Страницы: 96

Бренд: MacDon Страницы: 2

Бренд: Balanced Body Страницы: 4

Бренд: Balanced Body Страницы: 2

Reformer Trapeze Combination

Бренд: Balanced Body Страницы: 164

Бренд: Wacker Neuson Страницы: 50

Бренд: Balanced Body Страницы: 37

Бренд: mychway Страницы: 56

Бренд: Ganter Norm Страницы: 20

Бренд: Kellfri Страницы: 44

Бренд: Jäger Страницы: 36

Бренд: IMG STAGE LINE Страницы: 12

Бренд: Otto Bock Страницы: 44

Бренд: STRIKEMASTER Страницы: 12

Phastite PH-8-HANDTOOL

Бренд: Parker Страницы: 10

Бренд: X Training Equipment Страницы: 9

Бренд: Raider Страницы: 26

Бренд: Bard Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды