Sottoriva SVP08-0 Скачать руководство пользователя страница 50

Страница: 50 / 79

Rev. F
dated 02/07/2015

SVP08-0/1/2/3 - Code: 3529.0231.01

Service

Phone (+39) 0445.595.111

0715

Arc. 66-VII

7.3.1

Daily cleaning

parts in contact with foodstuffs;

slots;

gaps;

corners;

areas which are normally not accessible, after having removed the guards
mounted with screws;

the area beneath the machine, which can be accessed by pushing the machine
aside as indicated in

“3.1.4 Subsequent handling” on page 21

Proceed as follows to clean the machine:

1) remove any residue of dough/flour from all parts of the machine, using soft

plastic scrapers or soft brushes;

2) remove all dirt with a vacuum cleaner;

3) clean off any stains with water at ambient temperature.

7.3.1.1 Cleaning the dividing chamber and main piston (ref. 1 Fig. 13 on page

51)

Cleaning the dividing chamber is essential in order to ensure that the machine
operates normally.

To access the dividing chamber, proceed as follows:

- remove the interlocking upper guards, each of which is connected to a safety

microswitch;

- remove screws (

ref. 7 Fig. 13

);

- rotate the hopper and tip it onto its side as shown in

Fig. 13

;

- extract the blade (

ref. 2

Fig. 13

);

- clean thoroughly the blade (

ref. 2

Fig. 13

);

- extract the piston (

ref. 1

Fig. 13

);

- clean thoroughly the piston (

ref. 1

Fig. 13

);

- finally, carefully clean the piston (

ref. 1

Fig. 13

) housing chamber;

- refit the piston (

ref. 1

Fig. 13

);

- insert the knife (

ref. 2

Fig. 13

), paying attention to the lever (

ref. 9

Fig. 13

) which

should be inserted on the support knife (

ref. 8

Fig. 13

);

- put the hopper back into position and tighten the screws (

ref. 7 Fig. 13

Operator

On a daily basis

, at the end of each day of production, the machine must be kept

perfectly clean and hygienic, above all as regards the following areas:

Prohibition!

Do not use metal tools for removing dough/flour residue, nor for any
other cleaning operations.

Do not use acid or basic solutions to clean off stains; aggressive
chemical agents can damage the surfaces of the machine.

Do not direct jets of water at the machine to clean it.

Содержание SVP08-0
















































































Результаты поиска

Содержание SVP08-0

Отзывы:

Похожие инструкции для SVP08-0

Бренды по названию

Популярные бренды

Sottoriva SVP08-0, Инструкция по эксплуатации

Результаты поиска

Содержание SVP08-0

Отзывы:

Похожие инструкции для SVP08-0

Бренды по названию

Популярные бренды