Sottoriva SVP08-0 Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 79

background image

SVP08-0/1/2/3 - Code: 3529.0231.01

Rev. F

dated 02/07/2015

Arc. 66-IV

PT

0715

MV

0715

MC

0715

Service

Phone (+39) 0445.595.111

29

Protective measures:

The infeed opening has been protected by an impact-resistant plastic guard,
comprising four distinct parts, which is fixed to the frame by means of screws.

Protective measures:

The risk has been eliminated by inserting a guard between the cylinder and the
outfeed conveyor belt in the compression point which rotates towards the inside of
the roller.

Protective measures:

The top area of the machine has been protected by two steel guards connected to
two bayonet-type safety microswitches. These safety microswitches are also
connected to the upper hatches of the steel guards. Whenever one of the guards
is moved or a hatch is opened, the contacts on the respective microswitch open,
immediately cutting off the power supply to the machine.

The free end of each hatch, when closed, overlaps the metal guard cover (therefore
no openings exist). The microswitch is triggered when the hatch is raised by 25 mm
max from its resting position.

All other moving parts, such as drive mechanisms, belts, chains, etc. have been
rendered inaccessible by means of fixed guards. These guards may only be
removed under expressly specified circumstances and by the qualified technicians
indicated in each case in this Manual.

Danger

DANGER ZONE 2: area covered by the moving components (ref. ZP2
Fig. 15 on page 61).
NATURE OF RISK: Risk of entrapment, entrainment, crushing and shearing
of the upper extremities by moving parts.

Danger

DANGER ZONE 3: area comprising the outfeed conveyor belt and the roller
which drives it (ref. ZP3 Fig. 15).
NATURE OF RISK: Risk of entrapment and entrainment of the upper
extremities by moving parts.

Danger

DANGER ZONE 4: area comprising the top and sides of the machine (ref.
ZP4 Fig. 15).
NATURE OF RISK: Risk of entrapment, entrainment, shearing and cutting
of the upper extremities by moving parts.

«
...
29
30
31
32
33
...
»

Содержание SVP08-0
















































































Отзывы:

Нет отзывов

Похожие инструкции для SVP08-0

Бренд: JB-Lighting Страницы: 60

Бренд: Abus Страницы: 12

Бренд: Cannon Страницы: 70

Бренд: Sakai Страницы: 31

Бренд: Biosonic Страницы: 2

Бренд: Petzl Страницы: 7

RGB Studio Beam Driver

Бренд: SHOWTEC Страницы: 16

Бренд: My-Doc Страницы: 32

Бренд: Stone Страницы: 36

Бренд: Ocean Guardian Страницы: 41

Бренд: Com-Power Страницы: 10

LED Niova 150-F Pro 150W Bi Color

Бренд: Walimex Pro Страницы: 56

Бренд: Sport-thieme Страницы: 20

Бренд: BC BATTERY Страницы: 16

Carpark GP 7380 0080

Бренд: Dupline Страницы: 5

Бренд: Furuno Страницы: 10

Бренд: EcoNet Страницы: 83

Бренд: BOCK Страницы: 38

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды