Sony StorStation LIB-81 Скачать руководство пользователя страница 6

Страница: 6 / 102

Information Menu ......................................................86

Information.................................................................... 86
Inventory ....................................................................... 87

Appendix

If You Forget the Password ......................................89
Changing the Air Filter 1...........................................89
Changing the Air Filter 2...........................................91
Troubleshooting ........................................................92
Transporting the AIT Library ....................................93
Hardware Specifications...........................................94

Hardware ....................................................................... 94
Data Storage Capacity................................................... 95

Optional Accessories (sold separately) ..................96
SCSI Cable and Terminator Specifications .............96

SCSI Cable .................................................................... 96
SCSI Cable Length........................................................ 96

SCSI Specifications...................................................96

About SCSI Components .............................................. 97
About SCSI Bus ............................................................ 97

Error Code List ..........................................................98
Other Messages.......................................................100
Index .........................................................................101

Trademarks

• Sony, StorStation and Advanced Intelligent Tape are trademarks or registered trademarks of Sony Corporation in this

country, other countries, or both.

• Other product names are trademarks or registered trademarks of their respective owners in this country, other countries,

or both.

Содержание StorStation LIB-81







































































































Результаты поиска

Содержание StorStation LIB-81

Отзывы:

Похожие инструкции для StorStation LIB-81

Бренды по названию

Популярные бренды

Sony StorStation LIB-81, Руководство по эксплуатации

Результаты поиска

Содержание StorStation LIB-81

Отзывы:

Похожие инструкции для StorStation LIB-81

Бренды по названию

Популярные бренды