Sony StorStation LIB-81 Скачать руководство пользователя страница 89

Страница: 89 / 102

Appendix

Appendix

If You Forget the Password

If you forget the password, you will not be able perform configurations and
operations that require the password. If you forget the password, contact the
Service and Support Center.

Changing the Air Filter 1

• Depending on the shape of the front panel, the air filter and method for

changing the air filter may differ.

• Once a year, change the air filter of the AIT library. Contact your dealer if you

wish to buy additional air filters.

Air Filter: Model number ACY-FL81

Note

Make sure to clean the air filter once every three months.

Prepare a new air filter.

Turn off the AIT library power.

Содержание StorStation LIB-81







































































































Результаты поиска

Содержание StorStation LIB-81

Отзывы:

Похожие инструкции для StorStation LIB-81

Бренды по названию

Популярные бренды

Sony StorStation LIB-81, Руководство по эксплуатации

Результаты поиска

Содержание StorStation LIB-81

Отзывы:

Похожие инструкции для StorStation LIB-81

Бренды по названию

Популярные бренды