Sony StorStation LIB-81 Скачать руководство пользователя страница 99

Страница: 99 / 102

Appendix

* Verify that the transport screw was removed from the Shipping position.

“Unpacking” (page 13) in Chapter 2, “Installation”.

* • Verify that the bar code settings are correct.

“Setting the Bar Code” (page

44) in Chapter 3, “Basic Usage”.

• Verify that the bar code label is affixed properly.

“Preparing the

Cartridge” (page 25) in Chapter 2, “Installation”.

03050402

TableAxis

The Position Sensor is not normal. (Origin
was not detected.)

03050501

TableAxis

Destination not reached.

03050601

TableAxis

Fine tuning not possible.

03060101

ShutterAxis Timeout occurred during Close Sensor High

Wait.

03060201

ShutterAxis Timeout occurred during Open Sensor High

Wait.

03060901

Shutter sensor malfunction.

Mechanical Control Errors

Error code

Description

04000002

MechaCon

Parameter is incorrect.

04000003

MechaCon

Aborted.

04000004

MechaCon

More than 8 tape volumes present.

Remove extra cartridges from the library.

04000005

MechaCon

Cannot detect tape.

040000A0

MechaCon

Element address is incorrect.

040000A1

MechaCon

Element address does not exist.

AIT drive Errors:

Error code

Description

06000001

The drive status is not normal.

06000002

The drive SCSI ID was not set properly.

06000061

The drive cannot load the cartridge.

Bar code Errors*:

Error code

Description

07000001

A communication error occurred in the bar code reader.

07000002

A read error occurred in the bar code reader.

R-MIC Error:

Error code

Description

08000001

Could not receive data from R-MIC.

08000002

Transfer failure due to internal parameter error.

08000003

Data from R-MIC incorrect.

08000004

An R-MIC error occurred.

08000005

Internal memory error.

Ethernet Error:

Error code

Description

09000001

An Ethernet error occurred.

Mechanical Manager Error
(Byte2:Axis, Byte1:Class, Byte0:SubClass) (Continued)

Error code

Description

Содержание StorStation LIB-81







































































































Результаты поиска

Содержание StorStation LIB-81

Отзывы:

Похожие инструкции для StorStation LIB-81

Бренды по названию

Популярные бренды

Sony StorStation LIB-81, Руководство по эксплуатации

Результаты поиска

Содержание StorStation LIB-81

Отзывы:

Похожие инструкции для StorStation LIB-81

Бренды по названию

Популярные бренды