Sony StorStation LIB-81 Скачать руководство пользователя страница 37

Страница: 37 / 102

Chapter 3 Basic Usage

Eject/Insert Menu

Use this menu to set and replace the cartridges.

“Replacing the Cartridges” (page 53) in Chapter 4, “Operating the AIT

Library”.

The following submenus are in the Eject/Insert Menu.

• “Eject From Library”

Ejects the cartridge from the AIT library.

• “Eject From Drive”

Ejects the cartridge from the AIT drive, but does not move it to a slot.

• “Insert Into Library”

Loads a cartridge into the AIT library.

Move Tape Menu

This menu moves the cartridges.

“Replacing the Cartridges” (page 53) in Chapter 4, “Operating the AIT

Library”.

SCSI Menu

The SCSI IDs and SCSI parities of the AIT library and AIT drives can be set.

“Setting the SCSI ID” (page 23) in C hapter 2, “Installation”.

Eject From

Library

Eject From Drive

Insert Into

Library

Eject / Insert

ENTER

Содержание StorStation LIB-81







































































































Результаты поиска

Содержание StorStation LIB-81

Отзывы:

Похожие инструкции для StorStation LIB-81

Бренды по названию

Популярные бренды

Sony StorStation LIB-81, Руководство по эксплуатации

Результаты поиска

Содержание StorStation LIB-81

Отзывы:

Похожие инструкции для StorStation LIB-81

Бренды по названию

Популярные бренды