Sony DVCAM DSR-60, Руководство по обслуживанию

Страница: 16 / 324

1-6
DSR-80/80P/60/60P
Features
Chapter 1 Overview
10
Chapter 1 Overview
3
INPUT MODE display
Indicates the format of the currently selected video and
audio input signals.
VIDEO indicators : The corresponding indicator
lights when the selected video input signal is in
the composite analog, S-video, component analog,
or SDI (serial digital interface) format.
AUDIO CH-1, 1/2 indicators : The ANALOG,
AES/EBU or SDI indicator lights for the
corresponding format of the selected audio signal
being input to channel 1 (when in 2-channel
mode) or to channels 1 and 2 (when in 4-channel
mode).
AUDIO CH-2, 3/4 indicators: The ANALOG,
AES/EBU, or SDI indicator lights for the
corresponding format of the selected audio signal
being input to channel 2 (when in 2-channel
mode) or to channels 3 and 4 (when in 4-channel
mode).
QSDI : Lights when QSDI-format video and audio
input signals have been selected. When QSDI is
selected, all of the indicators in the VIDEO and
AUDIO groups go off.
4
INPUT SELECT buttons
Select video input signals and audio input signals.
VIDEO button : Each press of this button cycles
through four video signal selection options:
composite analog, S-video, component analog,
and SDI. When you select one of these options,
the corresponding VIDEO indicator in the INPUT
MODE display lights up.
AUDIO CH-1, CH-1/2 button : Each press of this
button cycles through three audio signal selection
options for audio channel 1 (when in 2-channel
mode) or channels 1 and 2 (when in 4-channel
mode): analog, AES/EBU, and SDI. When you
select one of these options, the corresponding
AUDIO indicator in the INPUT MODE display
lights up.
AUDIO CH-2, CH-3/4 button : Each press of this
button cycles through three audio signal selection
options for audio channel 2 (when in 2-channel
mode) or channels 3 and 4 (when in 4-channel
mode): analog, AES/EBU, and SDI. When you
select one of these options, the corresponding
AUDIO indicator in the INPUT MODE display
lights up.
QSDI : Press this button to select QSDI signals.
If the selected signal (except for analog audio) is not
supplied to the appropriate connector, the
corresponding indicator flashes in the INPUT MODE
display.
If the unit is not equipped with an optional DSBK-120/
120P SDI Input/Output Board, no SDI indicators light
in the INPUT MODE display no matter how many
times you press the INPUT SELECT buttons.
5
AUDIO REC (recording mode) SELECT button
Selects the audio mode for recording. Each press
toggles between 2-channel mode and 4-channel mode,
and the indicator corresponding to the selected option
lights in the AUDIO MODE display.
Note
This button works only when the unit is in EE mode.
6
AUDIO INPUT LEVEL control knobs
When recording, you can use these knobs to set audio
input levels for CH-1 (channel 1), CH-2, CH-3 and
CH-4, respectively.
You can make these knobs inoperative for an AES/
EBU, SDI or QSDI format digital audio input by
setting “DIGITAL INPUT” under the AUDIO
CONTROL menu item to “BYPASS”.
On how to use the menu, see Chapter 4 “Menu Settings”.
Location and Function of Parts
Chapter 1 Overview
Chapter 1 Overview
11
COUNTER SELECT EJECT REW PLAY F FWD STOP REC
COUNTER
TC
U-BIT
HOURS MINUTES SECONDS FRAMES
REC INHIBIT
NOT
EDITABLE
REMOTE EDIT MODE CIip Link
)
0
6 r
p
2
Display section (B) and COUNTER SELECT button
3
Time counter display
Indicates the following:
• Time data : CNT (count value of the time counter),
time code, or user bit data
• Digital hours meter’s count value : time total for
unit’s operating hours, drum usage hours, etc.,
(selectable via the digital hours meter display menu).
• Error messages and alarm messages (see page 73)
4
Tape end alarm indicator
L
Starts flashing when the tape’s remaining capacity is
for about 2 minutes.
5
REC INHIBIT indicator
Lights when the REC/SAVE switch on the loaded
cassette is in the SAVE position.
6
NOT EDITABLE indicator
Lights during playback of a tape that contains a DV-
format recording. DV-format recordings can be used
as source material for editing, but editing functions
such as setting IN/OUT points cannot be used.
This indicator also lights when the audio recording
mode selected on this unit does not coincides with that
of the loaded tape.
1
COUNTER SELECT button
Selects the type of time data to be shown in the time
counter display. Each press of this button cycles
through three indicator display options: COUNTER
(CNT: count value of the time counter), TC (time
code), and U-BIT (user bits).
Note
If the REMOTE/LOCAL switch is set to REMOTE,
the COUNTER SELECT button does not operate
while the tape is moving. In this case, make the time
data selection via the remote equipment that is
connected to the REMOTE connector on the rear
panel.
2
Time data type indicators
One of the three indicators (COUNTER, TC, and U-
BIT) lights to indicate the type of time data currently
shown in the time counter display.
COUNTER : CNT (count value of the time counter)
TC : SMPTE time code (DSR-80) or EBU time code
(DSR-80P)
U-BIT : User bit data
1
COUNTER SELECT button
2
Time data type indicators
3
Time counter display
9
EDIT MODE indicator
0
REMOTE indicator
8
ClipLink indicator
7
Cassette memory indicator
4
Tape end alarm indicator
5
REC INHIBIT indicator
6 NOT EDITABLE indicator