Sony DVCAM DSR-60, Руководство по обслуживанию

Страница: 34 / 324

1-24
DSR-80/80P/60/60P
46
Chapter 4 Menu Settings
Chapter 4
Menu Settings
Menu contents (Continued)
Menu Contents
TAPE PROTECTION [Tape protect]: Settings related to
tape and video head protection Description of settings
FROM STOP [> From
STOP]: Set the time to
switch from stop mode to
tape protection mode and
select the mode for
protecting the video
heads and video tape.
STOP TIMER [>> STP timer]:
Set the time to switch from
stop mode to tape protection
mode.
30 MIN [>>> 30 min] to 0.5 SEC [>>> 0.5 sec]: Select time
from 16 settings ranging from 0.5 seconds to 30 minutes in
steps of 0.1 second.
Factory default setting: 8MIN [>>> 8min]
NEXT MODE [>>> Next mode]:
Select tape protection mode
when time set in STOP
TIMER setting elapses.
∗
STANDBY OFF [>>> STANDBY]: Standby off mode
TENSION RELEASE [>>> T.RLSE]: The tape tension is
released, but the picture can still be seen on the monitor.
Note
When the unit is in tension release mode, the head drum is
still rotating, so the picture can be output and monitored. That
is, it is still in “standby on” mode (i.e. is on standby).
Therefore, care should be taken over the setting if it is
critically important whether the unit is in “standby on” or
“standby off” mode (for example when the unit is used for
broadcasting).
FROM STILL [> From
STILL]: Set the time to
switch from still search
mode or playback pause
mode to tape protection
mode. Also select the
type of tape protection
mode to follow still search
mode when the set time
elapses (playback pause
mode is always followed
by tension release mode).
STILL TIMER [>> STL timer]:
Set the time to switch from
still search mode or
playback pause mode to
tape protection mode.
30 MIN [>>> 30 min] to 0.5 SEC [>>> 0.5 sec]: Select time
from 16 settings ranging from 0.5 seconds to 30 minutes in
steps of 0.1 second.
Factory default setting: 8MIN [>>> 8min]
NEXT MODE [>>> Next mode]:
Select the type of tape
protection mode to follow
still search mode when the
time set in “STILL TIMER”
elapses.
∗
STEP FWD [>>> Step]: The tape is advanced at
1
/
30
normal
speed for 2 seconds.
STANDBY OFF [>>> STANDBY]: Standby off mode
TENSION RELEASE [>>> T.RLSE]: The tape tension is
released, but the picture can still be seen on the monitor.
Note
When the unit is in step forward or tension release mode, the
head drum is still rotating, so the picture can be output and
monitored. That is, it is still in “standby on” mode (i.e. is on
standby). Therefore, care should be taken over the setting if
it is critically important whether the unit is in “standby on” or
“standby off” mode (for example when the unit is used for
broadcasting).
TIME CODE [Time code]: Settings related to the time code
generator Description of settings
TC EE OUT MODE [>TC out mod]: This only appears when
the optional DSBK-130/130P Timecode Input/Output Board
is installed.
It controls the phase of the LTC signal output when
recording timecode and in “STOP REC” mode (forced EE
mode).
∗
MUTE [>>mute]: Output no timecode.
THROUGH [>> through]: Output LTC with the phase
synchronized to the signal input to the TIME CODE IN
connector. Use this mode when the signal input to the
VIDEO IN connectors is not synchronized to the reference
video signal. (See the example configuration on page 48.)
VIDEO INPUT PHASE [>> V input]: Output LTC with the
phase synchronized to the input video signal. Use this
mode when using the video input in a bridging (loop-
through) connection. (See the example configuration on
page 48.)
VIDEO OUTPUT PHASE [>> V output]: Output LTC with the
phase synchronized to the output video signal. Use this
mode when using a bridging (loop-through) connection
from the output video to the input video. (See the example
configuration on page 49.)
Chapter 4 Menu Settings
47
Chapter 4
Menu Settings
Menu contents (Continued)
VIDEO CONTROL [Video]: Settings related to video
control Description of setting
STILL MODE [> STILL mod]: Determine whether the image
of a whole frame or a field is output in still playback mode.
FRAME STILL [>> Frame]: Output the image of a whole
frame.
∗
FIELD 1 STILL [>> Field 1]: Output the image of field 1 only.
FIELD 2 STILL [>> Field 2]: Output the image of field 2 only.
(Only on DSR-80)
SETUP REMOVE [> Setup rmv]: Determine whether or not to
remove black setup from analog video input signals.
∗
OFF [>> OFF]: Do not remove black setup.
ON [>> ON]: Remove black setup.
(Only on DSR-80)
SETUP ADD [> Setup add]: Determine whether or not to add
black setup to analog video output signals.
∗
OFF [>> OFF]: Do not add black setup.
ON [>> ON]: Add black setup.
SYNC ON GREEN: When outputting RGB signals from the
COMPONENT VIDEO Y, R–Y, and B–Y/RGB OUT
connectors, select whether or not to include a sync signal
in the green signal.
∗
ON [>>ON]: Include a sync signal (use the RGB three-wire
mode).
OFF [>>OFF]: Do not include a sync signal. (Use the RGB
four-wire mode, and output the sync signal from the REF
VIDEO OUT connector.)
CC(F1)BLANK [>CC1 blank]: Select whether or not to blank
the closed caption first field signal.
∗
OFF [>>OFF]: Do not blank.
ON [>>ON]: Blank.
CC(F2)BLANK [>CC2 blank]: Select whether or not to blank
the closed caption second field signal.
∗
OFF [>>OFF]: Do not blank.
ON [>>ON]: Blank.
REF LEVEL [> REF Level]: Select reference audio level.
AUDIO CONTROL [Audio]: Settings related to audio
control Description of setting
DIGITAL INPUT [> Digi. Input]: Enable or disable the AUDIO
INPUT LEVEL control knobs to work for AES/EBU, SDI, or
QSDI format digital audio input.
∗
VARIABLE [>> Variable]: Enable the control knobs.
BYPASS [>> Bypass]: Disable the control knobs.
REC POINT MUTE [> REC pt mute]: Determine whether or
not to mute audio at the joints of recordings.
∗
OFF [>> OFF]: Mute.
ON [>> ON]: Do not mute.
Select the level from among the following three:
–12dB [>> –12dB], –18dB [>> –18dB], and
–20dB [>> –20dB]
Factory default setting: –20 dB (DSR-80), –18 dB (DSR-
80P)
MENU GRADE [Menu grade]: Selection of menu items to
be displayed Description of settings
Determine whether to display basic items only or both basic
and enhanced items on the monitor screen and on the time
counter display when using the menu.
∗
BASIC [> Basic]: Display basic items only.
ENHANCED [> Enhanced]: Display both basic and enhanced
items.
OUTPUT LEVEL [>OUT Level]: Select the audio output
reference level.
Select the level from the following three settings: *+4dB
[>>+4dB], 0dB [>>0dB], –6dB [>>–6dB],
AUDIO MUTE [>Audio mute]: Select whether or not to mute
the output until the audio signal has stabilized, in the
transition from still/search mode to playback.
ON [>>ON]: Mute.
∗
OFF [>>OFF]: Do not mute. (This reduces the time delay
until the audio signal is output.)
Notes
• In the transition from the stop mode to playback, muting is
always applied until the audio signal has stabilized.
• The search speeds at which an audio signal can be output
vary from model to model.