Sony BVP-550, Руководство по обслуживанию

Страница: 920 / 924

3-14(E)
BVP-550
Page Ver. Item Settings Contents
PRE KNEE/ WHITE CLIP XXX (
[XX]
) Adjusts the white clip level.
ZEBRA
WHITE CLIP
[ON]
, OFF Turns the white clip function on and off.
ZEBRA1 LEVEL, XXX (
[XX]
) Sets the center value and range for the zebra 1 signal detection.
RANGE
ZEBRA2 LEVEL XXX (
[XX]
) Sets the detection value for the zebra 2 signal.
Z.DISP 1,2, 1&2 Selects a zebra signal to be displayed on the viewfinder.
1
: Zebra 1 signal
2 : Zebra 2 signal
1&2 : Both zebra 1 and 2 signals are displayed at the same time.
TEST 1, 2,
[OFF]
Selects a TEST signal to be output in setting each item on the
PREKNEE/ZEBRA page.
1
: Outputs the sawtooth test signal
2 : Outputs the 3-step waveform test signal
OFF : No test signal is output
VTR/CCU VTR R-Y XXX (
[XX]
) Adjusts the R-Y color-difference signal level.
VTR B-Y XXX (
[XX]
) Adjusts the B-Y color-difference signal level.
CCU Y SAMP XXX (
[XX]
) Adjusts the level of the sample pulse to be mixed with the Y signal.
CCU R-Y SYNC XXX (
[XX]
) Adjusts the level of the sync pulse to be mixed with the R-Y signal.
CCU B-Y SAMP XXX (
[XX]
) Adjusts the level of the sample pulse to be mixed with the B-Y signal.
RGB OFFSET XXX (
[XX]
) Adjusts the G signal level.
TEST 1, 2,
[OFF]
Selects a TEST signal to be output in setting each item on the VTR/CCU page.
1
: Outputs the sawtooth test signal
2 : Outputs the 3-step waveform test signal
OFF : No test signal is output
CB ON,
[OFF]
Turns on and off the camera color-bar signal to be output in setting
each item on the VTR/CCU page.
IRIS LEVEL XXX (
[XX]
) Adjusts the auto-iris level.
APL RATIO XXX (
[0]
) Sets the way the iris is automatically adjusted. -99 (PEAK)
↔
99 (AVERAGE)
COLOR 1.10 COLOR REF Press MENU SEL Makes a color reference to compensate the difference in colors
SETUP (SELF) switch to execute. between OHBs using a single camera. (Locate the desired colors of a
Macbeth chart within the gate marker of VF and measure. To abort a
processing during execution, press MENU SEL switch.)
m)
1.10 COLOR SETUP Press MENU SEL Automatically calculates the color matrix from the reference. (Locate the
(SELF) switch to execute. desired colors of a Macbeth chart within the gate marker of VF and measure.
To abort a processing during execution, press MENU SEL switch.)
n)
1.10 (OHB MATRIX) Compensates the OHB matrix to adjust the difference between OHBs or
G-R, B-R -99 to 99 (
[0]
) cameras (sets an optional value as the constant for G-R, B-R, R-G,
R-G, B-G B-G, R-B and G-B).
r)
R-B, G-B
1.10 OHB MTX
[ON]
, OFF Turns the OHB matrix compensation on and off.
1.10 CM ADD LVL
[0]
to 16 For fine adjustment in color-setup operation. Compensates the
caluculation value for the color selected by the CM ADD COLOR in 16
steps and recalculates the OHB matrix. (Selecting 0 turns off the function.)
s) t)
1.10 CM ADD
[0]
to 17 For fine adjustment in color-setup operation. Select a color to be
COLOR compensated from 18 colors of the Macbeth chart with the gate marker
of VF. Recalculates the OHB matrix
t)
m) When performing compensation between two or more cameras, use the MSU.
n)
Differing from the color-setup operation by plural cameras, a data transfer is not performed.
Execute to recalculate. After execution, the color matrix data is temporarily reflected in the OHB matrix of the System Config menu.
Execute the OHB FILE STORE of the Triming menu to store the color matrix data.
r) Adjust with the MATRIX of the Paint menu turned OFF. Execute the OHB FILE STORE to store the adjustment values.
s) The compensation value is temporarily reflected in the OHB matrix of the System Config menu after execution of the COLOR
SETUP(SELF). Execute the OHB FILE STORE of the Triming menu to store the value.
The higher you set the value of the CM ADD LVL, the more the weights are assigned to the color selected by the CM ADD COLOR.
The compensation is performed so as to entirely minimize the error, while reducing the error for the weights-assigned color.
t) After powered off once following the completion of color-setup operation, recalculation is not performed.
3-1. Setup Menu
3-1-6. System Config Menu