Sony BVP-550, Руководство по обслуживанию

Страница: 271 / 924

3-13(E)
BVP-550
Page Item Settings Contents
PRE KNEE/ZEBRA WHITE CLIP XXX (
[XX]
) Adjusts the white clip level.
WHITE CLIP
[ON]
, OFF Turns the white clip function on and off.
ZEBRA1 LEVEL,WIDE XXX (
[XX]
) Sets the center value and range for the zebra 1 signal detection.
ZEBRA2 LEVEL XXX (
[XX]
) Sets the detection value for the zebra 2 signal.
Z.DISP 1,2, 1&2 Selects a zebra signal to be displayed on the viewfinder.
1: Zebra 1 signal
2: Zebra 2 signal
1&2: Both zebra 1 and 2 signals are displayed at the same time.
TEST 1, 2,
[OFF]
Selects a TEST signal to be output in setting each item on the PREKNEE/
ZEBRA page.
1: Outputs the sawtooth test signal
2: Outputs the 3-step waveform test signal
OFF: No test signal is output
VTR/CCU VTR R-Y XXX (
[XX]
) Adjusts the R-Y color-difference signal level.
VTR B-Y XXX (
[XX]
) Adjusts the B-Y color-difference signal level.
CCU Y SAMP XXX (
[XX]
) Adjusts the level of the sample pulse to be mixed with the Y signal.
CCU R-Y SYNC XXX (
[XX]
) Adjusts the level of the sync pulse to be mixed with the R-Y signal.
CCU B-Y SAMP XXX (
[XX]
) Adjusts the level of the sample pulse to be mixed with the B-Y signal.
RGB OFFSET XXX (
[XX]
) Adjusts the G signal level.
TEST 1, 2,
[OFF]
Selects a TEST signal to be output in setting each item on the VTR/CCU page.
1: Outputs the sawtooth test signal
2: Outputs the 3-step waveform test signal
OFF: No test signal is output
CB ON,
[OFF]
Turns on and off the camera color-bar signal to be output in setting each
item on the VTR/CCU page.
IRIS LEVEL XXX (
[XX]
) Adjusts the auto-iris level.
APL RATIO XXX (
[0]
) Sets the way the iris is automatically adjusted. -99 (PEAK)
↔
99 (AVERAGE)
OTHERS 1 FILTER,WHT MEM
[ON]
, OFF ON: A total of 8 settings of the white balance value can be saved in
conbination with the CC filter and WHITE BAL switch settings.
OFF: One white balance value can be saved for the WHITE BAL switch
setting A or B, for a total of 2 settings.
NTSC ENC
[WIDE]
, NRW Sets the band width of the Q signal for the NTSC color encoder.
ROTARY
[STD]
, RVS Selects the mode of MENU SEL switch (as turned counterclockwise when
viewed from the front.)
STD: Cursor moves downwards and a numeric value increases.
RVS: Cursor moves upwards and a numeric value decreases.
OWN CALL R, F&R , OFF Selects whether one or two TALLY lamps are lit corresponding to the
CALL button of camera adaptor pressed, or not. Or selects which TALLY
lamp is lit when the CALL button is pressed.
(This setting is valid in connection with CCU. When the camera is used
alone, it is always set to OFF.)
R: Rear TALLY lamp is lit.
F&R: Rear and front TALLY lamps are lit.
OFF: No TALLY lamp is lit corresponding to the CALL button.
CENTER H POS XXX (
[XX]
) Shifts horizontally the location of the center marker on the screen.
CENTER V POS XXX (
[XX]
) Shifts vertically the location of the center marker on the screen.
LENS VTR S/S TALK,
[RET2]
Selects the mode of VTR S/S SW of the lens and camera.
TALK: VTR S/S SW of lens functions as INCOM TALK SW (momentary)
and that of the camra as RET2 SW.
RET2: VTR S/S SW of lens functions as RET2 SW and that of the camera
as INCOM TALK SW.
VF ? DISPLAY
[ON]
, OFF Turns on and off the indication of ? mark at the top-right of the VF screen with
the DISP switch set to ON when the self-diagnosis result is NG (no good)and
(Continued) so on.
3-1. Setup Menu