Sonic Wave I Скачать руководство пользователя страница 64

Страница: 64 / 72

Page 64 of 72 / Confidential / Version 1.1

Eichweg 6 8154 Oberglatt Switzerland tel +41 (0) 44 850 0838 fax +41 (0) 44 850 0839 [email protected]

www.sonicemotion.com

14. Trouble Shooting

The most common error can occur when the system is turned on without the system

dongle attached. If this was the case you have to do some changes in the BIOS of

the Wave I processor.

1. Connect a monitor (VGA connector on the back side) and a keyboard to the
Wave I processor.

2. Plug in the system dongle

3. Start the Wave I processor and press and hold the delete key while the system
boots.

4. Go to :

“Advanced”

-> Onboard Device Configuration

-> Onboard LAN

-> [Enabled]

-> LAN Boot Rom -> [Enabled]

“Boot”

-> Hard Disk Drives

-> 1

Disk

-> [USB:OCZ RALLY2]

-> 2

Disk -> [1

FLOPPY DRIVE]

-> Boot Device Priority

-> 1

Device -> [USB:OCZ RALLY2]

“Power”

-> APM Configuration

-> Power On By PCI Devices

[Enabled]

-> Power On By PCIE Devices

[Enabled]

5. Press F10 to save and exit

6. Start the system with the dongle inserted

Содержание Wave I









































































Результаты поиска

Содержание Wave I

Отзывы:

Похожие инструкции для Wave I

Бренды по названию

Популярные бренды

Sonic Wave I, Руководство пользователя

Результаты поиска

Содержание Wave I

Отзывы:

Похожие инструкции для Wave I

Бренды по названию

Популярные бренды