SOMMER SPA-2 Скачать руководство пользователя страница 93

Страница: 93 / 111

The slope applied to the selected variable. Only available if

Decimals

is set to 1…5 or none. If

Decim-

als

is set as S (as source), no scaling is applied.

Offset

The offset applied to the selected variable.

Adjustment (Correction)

A measurement of the selected variable is triggered and the result displayed in the terminal win-
dow. If the measured value deviates from the correct value, the correct value can be entered. This
adjusts the value in

Offset

. The factor in

Scale

is not affected by this correction.

Test

A measurement of the selected variable is triggered and the result displayed in the terminal win-
dow.

S-TYP

One of the following sensor (or source) types:

S-TYP

Description and S-MEA options

off

No source (deactivated)

SPA-S

Variables of one of the SPA-ribbon sensors (straps)

SWE

Snow water equivalent

Density

Snow density

Ice

Fraction of ice (by volume)

Water

Fraction of water (by volume)

S-Temp

Sensor temperature

C-LF

Capacity at low frequency

C-HF

Capacity at high frequency

Ph-LF

Phase at low frequency

Ph-HF

Phase at high frequency

AIN

Analog input

AN1

Analog input 1 (preconfigured for snow depth measurement)

AN2

Analog input 2

AN3

Analog input 3

AN4

Analog input 4

Manual

Содержание SPA-2















































































































Результаты поиска

Содержание SPA-2

Отзывы:

Похожие инструкции для SPA-2

Бренды по названию

Популярные бренды

SOMMER SPA-2, Руководство пользователя

Результаты поиска

Содержание SPA-2

Отзывы:

Похожие инструкции для SPA-2

Бренды по названию

Популярные бренды