Soehnle Professional 3035 страница 97 Скачать руководство пользователя

Страница: 97 / 124

Example of reference statistics display:

Samples

Lightest part

24,448 g

Heaviest part

24,750 g

Deviation

0,302 g

Mean value

24,589 g

Printout of the statistics

Press the function key F1 "Print". Print output is only possible by using the interface on printer 1 "2795.14". If

necessary, the print image with the required print output must be adapted via the service program.

Storage of the mean value as reference weight for counting

Press F6 Accept.

Exiting the reference statistics without adopting the mean value

Press F5 Cancel.

6.7.8 Piece control

With the "piece check" function, piece goods can be dosed into a container or quantities checked.

Example: You want to fill 1000 counted parts with max. 3 parts tolerance into one container.

Example: You want to check several batches for compliance with the quantity.

To call up the piece control function, you must already be in count mode, i.e. you must have defined a

reference weight.

In level 2 Control functions, press the F5 key Contr.

Enter the desired number of pieces with the numeric keypad and confirm with

F6 Accept. Use the numeric keypad to enter the accepted tolerance in pieces and confirm with the F6 key.

If you want to define plus and minus tolerance separately, activate in the setting mode under program

settings / counting / +/- tolerance separately / on.

The display switches to the Count display view and the traffic light function with the special characters is

activated. The corresponding traffic light colour with special characters is displayed according to the actual

status on the scale for the setpoint.

Control status

Traffic light colour

Special characters

Below tolerance limit

Yellow

Within tolerance

Green

Setpoint reached exactly

Green

Above tolerance limit

Red

You can also have the difference to the target weight displayed in the top left-hand side of the secondary

display in figures with a + or - sign. Activate the secondary display with the F3 key Secondary display in level

4 Setting functions.

Display setpoint and tolerance

Press the Info key and then the F3 key.

Содержание 3035





























































































































Результаты поиска

Содержание 3035

Отзывы:

Похожие инструкции для 3035

Бренды по названию

Популярные бренды

Soehnle Professional 3035, Руководство пользователя

Результаты поиска

Содержание 3035

Отзывы:

Похожие инструкции для 3035

Бренды по названию

Популярные бренды