Soehnle Professional 3035 страница 111 Скачать руководство пользователя

Страница: 111 / 124

111

Switching points during control

If you want to transmit the control values via the interface, e.g. to a control traffic light or to a controller, an

I/O card must be installed in the device. This I/O card must be activated in setting mode under Program

settings / Control / IO preassignment with Execute. The output signals are assigned as follows:

Switching point

Signal

S1Weight weight over tolerance

S2not

active

S3Weight weight within tolerance

S4Weight weight under tolerance

S5empty message

S6Weight weight over tolerance

The individual inputs and outputs can be adjusted individually.

Dataset/printing within or outside tolerance

The release of a data record outside a defined tolerance range can be prevented or accepted. If a data record

is released outside the tolerance range, it is marked with a special character. Release or block in setting

mode under Program settings / Check / Data record out of tolerance.

6.8.6 Totalizing and picking

This function is also available in Control mode. This function can be used to totalize/pick control goods. The

totalizing functions are controlled with function keys on the control function level.

Totalize

means that the individual items are weighed one after the other, the weight in the totalizing memory is added

and the scale is unloaded after each individual weighing.

Picking

means that the weighed positions remain on the scale.

The weight is added in the total memory and the scale returns to zero without unloading.

It is not allowed to change measuring points during the picking process.

The selection Totalize or Pick

is made in the setting mode Program settings.

The selection applies to all connected weighbridges.

The following only refers to totalizing as an example.

Totalizing memory for several connected scales

A central totalizing memory is maintained for all connected scales.

Total memory capacity

A maximum of 999 bookings can be made in the totalizing memory.

The totalizing memory must then be cleared.

Содержание 3035





























































































































Результаты поиска

Содержание 3035

Отзывы:

Похожие инструкции для 3035

Бренды по названию

Популярные бренды

Soehnle Professional 3035, Руководство пользователя

Результаты поиска

Содержание 3035

Отзывы:

Похожие инструкции для 3035

Бренды по названию

Популярные бренды