background image

Lit. No. 78565, Rev. 02 

14 

November 1, 2019

If any button is pressed on the control, it will wake and 

check again for spreader connection. If no spreader is 

detected, it will act as described above. If a spreader 

is detected, it will transition to Ready Mode.

STARTING AND STOPPING SPREADER

To start the spreader

, press the ON/OFF button. The 

control backlights are illuminated when the vehicle 

ignition is ON and the spreader is connected. When 

the spreader is ON, the ON/OFF button and inner arc 

around the control knob will also illuminate.

To stop the spreader

, press the ON/OFF button 

again. 

 

The ON/OFF button also operates as an emergency 

stop when required.

NOTE: The vehicle ignition must be ON to start 

the spreader.

NOTE: If vehicle ignition is turned OFF while 

spreader is running, the motors will stop.

Control Knob

Indicator Lights 

(8 per Knob)

Status/Error Code 

Display (red)

Accessory 

Control Buttons

BLAST Button 

(maximum application)

ON/OFF Button

& Emergency Stop

POWERING THE CONTROL

Power is not applied to the control until the vehicle 

ignition is turned to ACC or ON. Once the control 

has power it performs a light check and displays the 

software version on the status display. The control 

then checks for a connected spreader. If no spreader 

is detected, the control does the following:

•  nC

 (no connection) appears on the red status 

d

isplay for five seconds;

•  A single beep will sound;

•  Control enters standby mode with no lights 

illuminated.

OPERATING THE SPREADER – CAB CONTROL

 WARNING

Never operate equipment when under the 

influence of alcohol, drugs, or medications that 

might alter your judgment and/or reaction time.

 WARNING

Never allow children to operate or climb on 

equipment.

 WARNING

Never exceed 45 mph (72 km/h) when loaded 

spreader is attached to vehicle. Braking 

distances may be increased and handling 

characteristics may be impaired at speeds 

above 45 mph (72 km/h).

 WARNING

Before starting the spreader, the driver shall 

verify that all bystanders are a minimum of 

25 feet away from operating spreader.

Содержание Drop Pro 600

























Отзывы: