background image

Lit. No. 78565, Rev. 02 

22 

November 1, 2019

TROUBLESHOOTING GUIDE

Please see your distributor for service. The troubleshooting reference table below may guide you in diagnosing 

the issue.

For a reference table of the cab control error codes, see the Operating the Spreader – Cab Control section of this 

manual.

Before servicing the spreader:

•  Review all safety information.
• 

Confirm that all electrical connections are tight and clean.

• 

Confirm that nothing is jammed in the hopper.

Problem

Possible Cause

Suggested Solution

No power to cab control. 

Ignition and control switches ON; 

control knob indicator lights not 

illuminated.

1.  Control is in standby mode. 

Spreader is not connected.

1.  Press any button on control to wake.

2.  Control connector plug is loose.

2.  Check plug connection at cab control.

3.  Switched accessory connection 

is poor, or faulty battery.

3a. Check for low battery.
3b. Check switched accessory 

connection.

4.  Blown fuse.

4.  Replace spreader vehicle battery 

cable fuse.

5. Vehicle control harness is damaged. 5.  Repair or replace damaged wires or 

harness as required.

Cab control shuts down.

Unplug the spreader harness and tag out, if required, 

before performing any of the following repairs.

1.  Cross-reference displayed error 

code with list on page 16−17.

1a. See suggested solution on page 16−17.

1b. Reset the control by pressing the 

ON/OFF button.

2. Poor electrical conditions.

2a. Clean or replace connectors.
2b. Apply dielectric grease.

3. Electrical short.

3.  Check electrical connections.

Turning control knob does not 

change motor speed. 

Control is 

powered ON.

Unplug the spreader harness and tag out, if required, 

before performing any of the following repairs.

1.  Malfunctioning cab control.

1.  Replace cab control.

2.  Malfunctioning motor.

2.  Replace motor.

3.  Malfunctioning spreader module.

3.  Replace spreader module.

Spreader does not operate.

Unplug the spreader harness and tag out, if required, 

before performing any of the following repairs.

1.  Wire harness is damaged or has an 

open circuit between cab control 

and spreader.

1a. Check plug connections at cab 

control and spreader.

1b. Check wire connections at vehicle 

battery and fuse.

1c. Check motor connections.

2.  Overloaded condition has triggered 

a time-out, or damaged motor or 

module.

2a. Wait 60 seconds for time-out to 

expire.

2b. Check motor. Repair or replace.
2c. Replace module.

Содержание Drop Pro 600

























Отзывы: