background image

3

Item     

Quantity 

P/N 

 

Description

   

 

87B728   

Dome & Solenoid Valve Assembly

   

 

6L200DH 

Stainless Steel Studs

   

 

6L65F   

Washers 

   

 

6L30K   

Nuts

   

 

1L28B   

Close Nipple

   

 

1L764B   

Ball Valve 

   

 

1L69B   

Pipe Plug 

   

 

1L37B   

Street Tee 

   

 

1L545A-2 

DIN Connector Cable

10 

   

 

5L150A   

Cable Ties 

11 

   

 

5L57C   

Cord Grip

12 

   

 

5L57C-2  

O-Ring for Cord Grip

13 

   

 

5L57C-1  

Nut for Cord Grip

14 

   

 

4L406B   

Delay Timer 

15 

   

 

6L139CG 

Self Tapping Screw

16 

   

 

5L75J   

Female Disconnect 

17 

   

 

87A455   

Piping Assembly

18 

   

12 ft. 

 

1L142BC 

Tubing

19 

   

 

87P31   

Installation Instructions (This Document), not shown

PARTS INCLUDED IN KIT

Please make sure your kit contains all 

of the parts and quantities noted in the 

Item  and  Description  sections  above, 

and  assure  that  none  of  the  parts  are 

damaged  before  starting  to  install  this 

kit.    Report  any  damaged  or  missing 
parts to the Smith & Loveless, Inc. 

Parts 

Department at (800) 922-9048

.

Your kit contains the following parts:

1

2

3

4

5

6

7

8

9

10

11

13

12

14

15

17

18

16

This manual is used for kits 

H87A457  and  H87A459. 

Please  note  if  you  have 

received kit H87A459 that 

parts 1-4 on the list at the 

left were installed on your 

pump  at  the  S&L  factory 

and will not be found in the 

kit.

Содержание SONIC START STREAMLINE H87A457

























Отзывы: