SMITH & LOVELESS SONIC START STREAMLINE H87A457 Скачать руководство пользователя страница 22

Страница: 22 / 24

SONIC START

Prime Sensing

Probe needs to be replaced.

6. If additional information or assistance is

needed, call your

Smith & Loveless,

Inc. Representative

or the Smith &

Loveless, Inc. Parts Department at

(800) 922-9048

Troubleshooting 4

The Sonic Start

Prime Sensing Probe has a

flashing

Red

light. The flashing

Red

light means

there is an overload or short circuit in the

SONIC

START

wiring or a problem with the

SONIC

START

Prime Sensing Probe.

1. If the

Red

light is flashing, first check

the wiring to the control panel and

back. If you find a loose connection,

this was the problem and the pump

will perate normally now. If not, go to

Step 2.

2. If, after checking all of the wiring

items and it does not correct the

flashing

Red

light, then check the

Din Connector Cable (Item 9).

Make sure the

Din Connector Cable

(Item 9)

is securely screwed in and

attached to the

SONIC START

Prime Sensing Probe. If it was not

securely connected and now it is, thus

resolving the problem, the pump will

now operate normally. If not, go to

Step 3.

3. If the

Red

light is still flashing, switch

the

SONIC START

Operating

Module out with another

SONIC

START

Operating Module. If this

resolves the problem, you have a

defective

SONIC START

Operating

Module. If not, go to

Step 4

4. If this still does not solve the problem,

then switch out the

SONIC START

Prime Sensing Probe itself. The

SONIC START

Prime Sensing

Probe needs to be replaced.

5. If additional information or assistance

is needed, call your

Smith & Loveless,

Inc. Representative

or the Smith &

Loveless, Inc. Parts Department at

(800) 922-9048

TROUBLESHOOTING

GUIDE

Содержание SONIC START STREAMLINE H87A457

























Результаты поиска

Содержание SONIC START STREAMLINE H87A457

Отзывы:

Похожие инструкции для SONIC START STREAMLINE H87A457

Бренды по названию

Популярные бренды

SMITH & LOVELESS SONIC START STREAMLINE H87A457, Инструкция по установке и эксплуатации

Результаты поиска

Содержание SONIC START STREAMLINE H87A457

Отзывы:

Похожие инструкции для SONIC START STREAMLINE H87A457

Бренды по названию

Популярные бренды