Smiley Lifting Solutions SpyderCrane 300 Series Скачать руководство пользователя страница 30

Страница: 30 / 51

Inspect, Clean, and Replace The Fuel Filter and Fuel/Water Separator (300

/500

/700

Series)

Vehicle Start Condition



300

/500

/700

Series



Travel Mode



OFF

Personnel and Time Needed



1 Person



Standard PPE



<5 minutes

Tools and Equipment Needed



Replacement Fuel Filter Element



Replacement Fuel/Water Separator

Screen (if replacing)

WARNING: You MUST leave the SPYDERCRANE OFF and allow enough time for the engine to cool before performing ANY maintenance.

Open the Engine Compartment.

Close the Fuel Flow Valve above the Fuel Filter Case.

Unfasten the Retaining Ring above the Fuel Filter Case to remove the case.

Remove and dispose of the Fuel Filter.

Wash out the inside of the Fuel Filter Case with diesel fuel.

Insert a new Fuel Filter into the Fuel Filter Case.

Inspect the O

Ring at the top of the Fuel Filter Case for excessive wear, or damage.

Fasten the Fuel Filter Case back to the Fuel Filter Port and hand

tighten the retaining ring.

Open the Fuel Flow Valve above the Fuel Filter Case.

10.

Repeat Steps 1

10 for the Fuel/Water Separator, which is located below the Fuel Filter Case and uses the same case de-

sign.

11.

Pump the Manual Fuel Priming Pump 20 times to pump in fuel and pump out any air trapped in the fuel line.

Содержание SpyderCrane 300 Series




















































Результаты поиска

Содержание SpyderCrane 300 Series

Отзывы:

Похожие инструкции для SpyderCrane 300 Series

Бренды по названию

Популярные бренды

Smiley Lifting Solutions SpyderCrane 300 Series, Руководство оператора

Результаты поиска

Содержание SpyderCrane 300 Series

Отзывы:

Похожие инструкции для SpyderCrane 300 Series

Бренды по названию

Популярные бренды