SMC Networks EX260-FPS1 Скачать руководство пользователя страница 44

Страница: 44 / 48

- 43 -

No.EX

※※

-OMU1006-B

Table C-5 Validation

Checklist for validation

Device type/equipment identification

Version: HW/FW

Date

Creator

Test engineer

Remark

No.

Requirement (optional)

Yes

Remark

Have all the mandatory requirements for the "Planning" checklist
been met?

Have all the mandatory requirements for the "Assembly and
electrical installation" checklist been met?

Have all the mandatory requirements for the "Commissioning and
parameterization" checklist been met?

Does the parameterization of the safe outputs correspond to the
version and the actual connection of the controlled device?

Has the assignment of the valves to the outputs and the variables of
the safe application program been tested(online status in PROFIsafe
controller software)?

Has a function test been performed to check all safety functions, in
which the module is involved?

Have measures been taken to achieve a specific Cat.?

Do all cables correspond to the specifications?

Does the power supply correspond to the specifications for the
protective extra-low voltage (PELV) or safety extra-low voltage
(SELV)?

Have the voltage supply of PWR and PWR(V) from a power supply
unit been correctly implemented?

Is external protection of the module implemented (according to the
specifications in this user manual for supply voltage PWR and
PWR(V))?

Have measures been taken to prevent simple manipulation?

Are the requirements for the valves and cable installation observed
according to the SIL/SILCL/Cat./PL?

Are test intervals specified for testing the shutdown capability of the
actuators, if this is required to achieve a SIL/SILCL/Cat./PL?

Has it been ensured that any person intentionally starting hazardous
movements can only do so with a directly view of the danger zone?

Date

Signature (creator)

Date

Signature (test engineer)

2020-10-30 10:03

DL085648

Содержание EX260-FPS1

















































Результаты поиска

Содержание EX260-FPS1

Отзывы:

Похожие инструкции для EX260-FPS1

Бренды по названию

Популярные бренды

SMC Networks EX260-FPS1, Руководство по эксплуатации

Результаты поиска

Содержание EX260-FPS1

Отзывы:

Похожие инструкции для EX260-FPS1

Бренды по названию

Популярные бренды