SMC Networks EX260-FPS1 Скачать руководство пользователя страница 9

Страница: 9 / 48

- 8 -

No.EX

※※

-OMU1006-B



Adjustment and Operation



Set the switches by using a sharp-pointed screwdriver etc.

Caution: Ensure the tool does not damage the switches during this process.



Perform settings suitable for the operating conditions.

Caution: Incorrect settings can cause operation failure and unexpected actuator behaviour



Please refer to the PLC manufacturer's manual etc. for details of programming and addresses.

For the PLC protocol and programming refer to the relevant manufacturer's documentation.



Maintenance



Turn off the power supply, stop the supplied air, exhaust the residual pressure and verify the release of

air before performing maintenance.

There is a risk of unexpected malfunction.



Perform regular maintenance and inspections.

There is a risk of unexpected malfunction.



After maintenance is complete, perform appropriate functional inspections.

Stop operation if the equipment does not function properly.
Otherwise safety is not assured due to an unexpected malfunction or incorrect operation.



Do not use solvents such as benzene, thinner etc. to clean the SI unit.

They could damage the surface of the body and erase the markings on the body.
Use a soft cloth to remove stains.
For heavy stains, use a cloth soaked with diluted neutral detergent and fully squeezed, then wipe up the stains
again with a dry cloth.

2020-10-30 10:03

DL085648

Содержание EX260-FPS1

















































Результаты поиска

Содержание EX260-FPS1

Отзывы:

Похожие инструкции для EX260-FPS1

Бренды по названию

Популярные бренды

SMC Networks EX260-FPS1, Руководство по эксплуатации

Результаты поиска

Содержание EX260-FPS1

Отзывы:

Похожие инструкции для EX260-FPS1

Бренды по названию

Популярные бренды