background image

 

 

- 12 - 

 

No.EX

※※

-OMU1006-B 

 

 

1.4. Directive and standards 

The standards to which the SI Unit conforms are listed in the certificate issued by the approval body and in the 
EC declaration of conformity. 
 

1.4.1. Intended use 

The EX260-FPS1 is designed exclusively for use in a PROFIsafe system and fulfils the PROFINET 
guidelines as defined by PI (PNO). It can only perform its tasks in the system if it is used according to the 
specifications in this document. 

 

Only use the SI Unit according to the defined technical data and ambient conditions: refer to 

Section 5 

"Specifications"

 
 

1.5. Documentation 

 

1.5.1. Correctness and availability of documentation 

Always use the latest documentation for this product. Changes or additions to documentation can be found 
on the Internet (refer to: 

www.smcworld.com

). 

 

1.5.2. PROFIsafe user manuals: 

For the safe controller used 

For the failsafe PROFIsafe I/O modules used 

For PROFIsafe system function blocks 

 

Observe the information on PROFINET, and PROFIsafe which is available on the Internet 
(refer to: 

www.profisafe.net

). 

 
 

1.6. Abbreviations used 

Table 1-1 Abbreviations for safety requirements 

Abbreviation 

Meaning 

Standard 

Example 

SIL 

Safety integrity level 

IEC 61508 

SIL 2, SIL3 

SILCL 

SIL claim limit 

EN 62061 

SIL CL 3 

Cat. 

Category 

EN ISO 13849-1 

Cat. 2, Cat. 4 

PL 

Performance level 

EN ISO 13849-1 

PL d, PL e 

 

Table 1-2 General Abbreviations 

Abbreviation 

Meaning 

PELV 

Protective extra-low voltage according to EN 61140   

SELV 

Separated extra-low voltage according to EN 61140 

 
Explanations of terms and abbreviations used in the context of PROFIsafe: refer to 

"Appendix A: Glossary for 

PROFIsafe"

2020-10-30 10:03

DL085648

Содержание EX260-FPS1

















































Отзывы: