SMC Networks EX260-FPS1 Скачать руководство пользователя страница 19

Страница: 19 / 48

- 18 -

No.EX

※※

-OMU1006-B

3.2.1. PROFINET/Power connection

The SI Unit has two PROFINET communication connectors. If only one connector is used, cover the
unused connector with a seal cap so that the protection rating of IP67 is maintained.

Caution



Seal caps must be fitted to all unused bus connector ports to ensure an IP67 rating.



IP67 rating must be maintained to guarantee PROFIsafe functionality.



For reasons of EMC a secure connection to the cable shield must be established on the M12 PROFINET

connectors (BUS IN/OUT).



Power and PROFINET cables must be installed correctly.



The 24 V supply for logic (PWR connector) and the 24 V supply for the valves (PWR(V) connector) should

be protected with an external fuse.



All external supplies should have the 0 V connected to functional earth according to EN 60204-1.



A functional earth cable must be connected to the M3 terminal.



If this product is connected using power cables that are more than 30 m long or go outside of a building

then external protection devices should be added to protect against electrical surge damage.

Remarks

24 V (PWR(V))

0 V (PWR(V))

24 V (PWR)

0 V (PWR)

M12 4-pin plug

A-coded connector(PWR)

Fig. 3-4 Pin allocations of Power connectors

(BUS IN) Port1

Port type: MDI

(BUS OUT) Port2

Port type: MDI-X

Remarks

Description

Remarks

Description

TD+

Transmit data+

RD+

Receive data+

RD+

Receive data+

TD+

Transmit data+

TD-

Transmit data-

RD-

Receive data-

RD-

Receive data-

TD-

Transmit data-

M12 4-pin socket

D-coded connector

(BUS IN/OUT)

Fig. 3-5 Pin allocations of PROFINET communication connectors

2020-10-30 10:03

DL085648

Содержание EX260-FPS1

















































Результаты поиска

Содержание EX260-FPS1

Отзывы:

Похожие инструкции для EX260-FPS1

Бренды по названию

Популярные бренды

SMC Networks EX260-FPS1, Руководство по эксплуатации

Результаты поиска

Содержание EX260-FPS1

Отзывы:

Похожие инструкции для EX260-FPS1

Бренды по названию

Популярные бренды