SMC Networks D-F7K Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 42

background image

-34-

No.D-

※

S-OMG0006-C



Troubleshooting List

Problem

No.

Problem

Possible cause

Countermeasure

1

The switch output does not
turn OFF.
The Indicator light does not
turn OFF.

Malfunction due to
magnetic field

Keep the actuator 40 mm or more away from
adjacent actuators to avoid the influence of
magnetic fields. Install a magnetic shielding plate
between the actuators.

If a magnetic field source is present near the
actuator (electric welding machine conductor,
motor, strong magnet etc.), use a magnetic
shielding plate between the magnetic field source
and the actuator.

Improper setting
(mounting) position
(Narrow angle)

When the product operation range is larger than
the piston stroke range, position the product
away from the centre of the operation range.

2

The switch output does not
turn OFF.
The Indicator light does not
turn ON.

Product failure

Replace the Product.

3

The switch output does not
turn ON.
The Indicator light does not
turn OFF.

Product failure

Replace the Product.

4

The switch output does not
turn ON.
The Indicator light does not
turn ON.

Power supply failure

Supply the specified power supply voltage (when
the power supply voltage is zero or very low).

Incorrect wiring

Check and correct the wiring.

Improper setting
(mounting) position

If the product is operating near the limit of the
operating range, position the product to the
centre of the operating range.

Displacement from the
set position

If the mounting bracket or mounting screws are
loose, tighten them using the appropriate
tightening torque at the correct position.

Displacement of the
actuator stopping
position

When the stop position of the actuator piston is
inconsistent, take measures to stabilize the
position.

Reduction in magnetic
detection force
(demagnetization)

Keep the actuator 40 mm or more away from
adjacent actuators to avoid the influence of
magnetic fields. Install a magnetic shielding plate
between the actuators.

If a magnetic field source is present near the
actuator (electric welding machine conductor or
strong magnet), use a magnetic shielding plate
between the magnetic field source and the
actuator.

«
...
33
34
35
36
37
...
»

Содержание D-F7K











































Отзывы:

Нет отзывов

Похожие инструкции для D-F7K

BNI IOL-727-S51-P012

Бренд: Balluff Страницы: 20

Бренд: Qlogic Страницы: 135

SANbox2 SANbox2-64

Бренд: Qlogic Страницы: 224

Бренд: Lantronix Страницы: 2

ETHERNET Accessories 852 852-0111

Бренд: WAGO Страницы: 38

TECMA Silence Marine

Бренд: Thetford Marine Страницы: 9

Nexoos 370 Series

Бренд: Soyntec Страницы: 7

Бренд: Accton Technology Страницы: 7

Бренд: Datavideo Страницы: 64

Бренд: Alloy Страницы: 33

Бренд: Black Box Страницы: 76

Бренд: Goobay Страницы: 16

Бренд: Top View Страницы: 13

AVS-OP-1616-567SD

Бренд: AMX Страницы: 1

Бренд: Yacoub Automation GmbH Страницы: 45

Бренд: Datavideo Страницы: 90

Бренд: Microsens Страницы: 42

Бренд: Hirschmann Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды