SMC Networks D-F7K Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 42

background image

-11-

No.D-

※

S-OMG0006-C

○Amplifier unit

Element

Description

Indicator light (OUT1)

Indicates the output status of OUT1.
The OUT1 light is ON (Green) when the output is ON.

Adjustment trimmer (OUT1)

For adjusting the detection range of OUT1.

Indicator light (OUT2)

Indicates the output status of OUT2.
The OUT2 light is ON (Orange) when the output is ON.

Adjustment trimmer (OUT2)

For adjusting the detection range of OUT2.

Indicator light (READY)

The READY light is ON (Red) when the sensor unit detects the magnetic field.
The detection ranges of OUT1 and OUT2 should be adjusted when this light is ON.

Lead wire

Lead wire for power supply and outputs. (3 m)

Through hole

Hole for direct mounting.

Sensor socket

For connecting the sensor.

Adjustment trimmer (ADJ.)

For adjusting the sensor unit when it is connected for the first time. Refer to Offset
adjustment (page

) for details.

Indicator light (OFF SET)

The OFFSET light is ON (Red) when the adjustment is completed.

«
...
10
11
12
13
14
...
»

Содержание D-F7K











































Отзывы:

Нет отзывов

Похожие инструкции для D-F7K

Бренд: AbleNet Страницы: 2

Бренд: Qlogic Страницы: 135

SANbox2 SANbox2-64

Бренд: Qlogic Страницы: 224

Бренд: HPM Страницы: 4

Бренд: Black Box Страницы: 2

SRS Lighting DTS16F-DIN

Бренд: plasa Страницы: 4

Бренд: LOVATO ELECTRIC Страницы: 37

Бренд: Zamel Страницы: 2

tecatlantis EASY LED CONTROL 2 PLUS

Бренд: Aquatlantis Страницы: 4

Бренд: Bühler technologies Страницы: 20

Бренд: Articona Страницы: 2

Бренд: Sunix Страницы: 55

Ethernet Networks and Web Management

Бренд: GarrettCom Страницы: 12

IBPO-HB50SR-XFP

Бренд: Net Optics Страницы: 53

Бренд: axing Страницы: 4

Бренд: Eneo Страницы: 19

Бренд: ZIMCO Страницы: 7

Бренд: Goobay Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды