Smartgen HGM9120 Скачать руководство пользователя страница 47

Страница: 47 / 58

HGM9120 Genset Controller

HGM9120 Genset Controller Version: 1.0 2014-04-14 Page 47 of 58

mode;

all

the

keys

except

are inactive, and

will show in the first line of LCD display.

Auto Mode Invalid

When input is active, controller won

‟t work under

Auto mode.

key and simulate auto key

input does not work.

Reserved

Inhibit Alarm Stop

All shutdown alarms are prohibited except
emergence stop.(Means battle mode or override
mode)

Aux Instrument Mode

All outputs are prohibited in this mode.

Reserved

Reset Maintenance

Controller will set maintenance time and date as
default when input is active.

Reserved

Aux. High Temp

Connected sensor digital input.

Aux. Low OP

Connected sensor digital input.

Reserved

Remote Start
(Off Load)

Auto

mode, when input is active, genset can be

started  automatically  and  NOT  take  load  after
genset  normal  running;  when  input  is  inactive,
genset will stop automatically.
Note: Dedicated remote start input port is fitted (If
active, it is remote start on-load input port).

Aux. Manual Start

Manual

mode, when input active, genset will

start automatically; when input inactive, genset
will stop automatically

Reserved

Simulate Stop key

An external button can be connected and pressed
as simulate panel.

Simulate Manual key

Reserved

Simulate Auto key

An external button can be connected and pressed
as simulate panel.

Simulate Start key

Simulate G-Load key

This is simulate generator close/open key.

Simulate M-Load key

This is simulate mains close/open key.

Reserved

Содержание HGM9120



























































Результаты поиска

Содержание HGM9120

Отзывы:

Похожие инструкции для HGM9120

Бренды по названию

Популярные бренды

Smartgen HGM9120, Руководство пользователя

Результаты поиска

Содержание HGM9120

Отзывы:

Похожие инструкции для HGM9120

Бренды по названию

Популярные бренды