Smartgen HGM9120 Скачать руководство пользователя страница 58

Страница: 58 / 58

HGM9120 Genset Controller

HGM9120 Genset Controller Version: 1.0 2014-04-14 Page 58 of 58

14 FAULT FINDING

Symptoms

Possible Solutions

Controller no response with
power.

Check starting batteries;
Check controller connection wirings;
Check DC fuse.

Genset shutdown

Check the water/cylinder temperature is too high or not;
Check the genset AC voltage;
Check DC fuse.

Controller emergency stop

Check emergence stop button is correct or not;
Check whether the starting battery positive be
connected with the emergency stop input;
Check whether the circuit is open.

Low oil pressure alarm after
crank disconnect

Check the oil pressure sensor and its connections.

High water temp. alarm after
crank disconnect

Check the temperature sensor and its connections.

Shutdown Alarm in running

Check related switch and its connections according to
the information on LCD;
Check programmable inputs.

Crank not disconnect

Check fuel oil circuit and its connections;
Check starting batteries;
Check speed sensor and its connections;
Refer to engine manual.

Starter no response

Check starter connections;
Check starting batteries.

Genset running while ATS not
transfer

Check ATS;
Check the connections between ATS and controllers.

Содержание HGM9120



























































Результаты поиска

Содержание HGM9120

Отзывы:

Бренды по названию

Популярные бренды

Smartgen HGM9120, Руководство пользователя

Результаты поиска

Содержание HGM9120

Отзывы:

Бренды по названию

Популярные бренды