Smartgen HGM9120 Скачать руководство пользователя страница 12

Страница: 12 / 58

HGM9120 Genset Controller

HGM9120 Genset Controller Version: 1.0 2014-04-14 Page 12 of 58

4.2 KEY FUNCTIONS

Stop

Stop running generator in Auto/Manual mode;
Lamp test (press at least 3 seconds); Reset alarm
in stop mode; During stopping process, press this
button again to stop generator immediately.

Start

Start genset in Manual/Test mode.

Manual Mode

Press this key and controller enters in

Manual

mode.

Auto Mode

Press this key and controller enters in

Auto

mode.

Mute/Reset
Alarm

Alarming sound off; If there is trip alarm, pressing
the button at least 3 seconds can reset this alarm.

Gen Close/Open

Can control generator to switch on or off in manual
mode.

Mains Close/Open

Can control generator to switch on or off in manual
mode.

Up/Increase

1) Screen scroll; 2) Up cursor and increase
value in setting menu.

Down/Decrease

1) Screen scroll; 2) Down cursor and decrease
value in setting menu.

Left

1) Screen scroll; 2) Left move cursor in setting
menu.

Right

1) Screen scroll; 2) Right move cursor in setting
menu.

Set/Confirm

1. Press the button will enter into parameter

configuration menu;

2. In settings menu confirms the set value.

Exit

1. Returns to the main menu;
2. In settings menu returns to the previous menu.

NOTE

: In manual mode, pressing

and

simultaneously will force

generator to crank. Successful start will not be judged according to crank disconnect

conditions, operator will have to crank the starter motor manually; when operator decides

Содержание HGM9120



























































Результаты поиска

Содержание HGM9120

Отзывы:

Похожие инструкции для HGM9120

Бренды по названию

Популярные бренды

Smartgen HGM9120, Руководство пользователя

Результаты поиска

Содержание HGM9120

Отзывы:

Похожие инструкции для HGM9120

Бренды по названию

Популярные бренды