Smartgen HGM9120 Скачать руководство пользователя страница 56

Страница: 56 / 58

HGM9120 Genset Controller

HGM9120 Genset Controller Version: 1.0 2014-04-14 Page 56 of 58

13 GSM SHORT MESSAGE ALARM AND REMOTE CONTROL

13.1 GSM SHORT MESSAGE ALARM

When controller detects alarm, it will send short message to phone automatically.

NOTE

All alarms about shutdown, trip and stop and trip will be sent to the pre-set phone.

Warnings are sent to the phone according to the pre-set.

13.2 GSM SHORT MESSAGE REMOTE CONTROL

Users send order message to GSM MODEM (SG361 module produced by Smartgen is

recommended), then controller will make actions according to this SMS order and pass back

corresponding operations information. Controllers only execute the orders by pre-set. Detail

orders as following:

No. SMS Orders

Pass back Information

Description

SMS
GENSET

GENSET ALARM

When genset is
shutdown alarm

status of genset

SYSTEM IN STOP MODE
GENSET AT REST

At rest status in
stop mode

SYSTEM

MANUAL

MODE
GENSET AT REST

At rest status in
manual mode

SYSTEM IN AUTO MODE
GENSET AT REST

At rest status in
Auto mode

SYSTEM IN STOP MODE
GENSET IS RUNNING

Running status in
stop mode

SYSTEM

MANUAL

MODE
GENSET IS RUNNING

Running status in
manual mode

SYSTEM IN AUTO MODE
GENSET AT RUNNING

Running status in
auto mode

SMS
START

GENSET ALARM

Generator

shutdown alarm
or trip alarm

Start genset

STOP MODE NOT START

Cannot

start

stop mode

SMS START OK

Start in manual
mode

AUTO MODE NOT START

Cannot

start

auto mode

SMS STOP
MODE

SMS STOP

SMS STOP OK

Set  as  stop  mode  or  send  out  stop
command;  the  genset  carries  out  stop
operation and enters into stop mode.

Содержание HGM9120



























































Результаты поиска

Содержание HGM9120

Отзывы:

Похожие инструкции для HGM9120

Бренды по названию

Популярные бренды

Smartgen HGM9120, Руководство пользователя

Результаты поиска

Содержание HGM9120

Отзывы:

Похожие инструкции для HGM9120

Бренды по названию

Популярные бренды