background image

Translated by R.Whitehead  10-3-2014    (my best effort – accuracy is not guaranteed) 

 

9 of 38 
 

6. Operation of the GPS-Logger 2 

 

6.1. Installation  

Due to the low weight and the compact desi.gn, installation is unproblematic. An attachment 
with Velcro on boards is sufficient and gives quick access to the memory card. 

 

Attention must be paid to ensure that the GPS antenna is pointing up and there are no 
shielding materials such as metal or carbon fibre above it.  
It has been shown that when used with 2.4 GHz telemetry systems the GPS-Logger should 
not be installed right next to the receiver antennas. 
 

The direction of the three axes of the acceleration sensors is printed on the label. 
The Z axis always points down when the antenna points upwards. The assignment 
X and Y depends on the direction of installation. 

 
 

6.2. Memory cards  

As memory card practically all commercial micro SD cards with FAT16 or FAT32 file system 
can be used. Also SDHC cards and memory capacities over 2 GB are supported. However 
not all cards are equally suitable, since some cards exhibit an unfavourable behaviour with 
continuous storing of data. If an unsuitable card is used, the recording may run intermittently 
or even stop.  
We recommend the use only with the card provided or available as an accessory from us.  

 

The card is inserted into the slot on the back and 
pushed in until it clicks and is flush. The GPS-Logger 2 
does not have an ejector for the memory card so the 
card is simply pulled out again with the fingers. If 
necessary a smll strip of adhesive tape helps. 
 

 

6.3. Meaning of the LED  

The GPS-Logger 2 has three coloured LEDs.  
After switching on a run of the three LED indicates the internal initialization.  
 
In operation there are the following signals:  

• 

orange LED shines permanently  

 GPS ready, but  still no 3D fix, i.e. GPS positioning not yet possible 

•  green LED shines permanently  

 GPS and 3D fix ready, i.e. GPS positioning available 

• 

orange LED flashes at the set recording rate  

 GPS recording data, but still no 3D fix 

•  green LED flashes at the set recording rate  

 GPS recording data, 3D fix  

•  red LED flashes  

 no memory card pushed  in. 

 

Содержание gps-logger 2







































Отзывы: