Skope 400 A Скачать руководство пользователя страница 51 | Manualshive

Страница: 51 / 68

Skope 400 A Скачать руководство пользователя страница 51

47

12.8.3 SET DETACHMENT TIME

The detachment time can be modified using the arrow buttons and is measured in minutes
and seconds with a resolution of 1 second.

The value can be changed with “Up/Down”. By pressing “OK”, you can store this parameter
and go to the next one. The value will remain stored even if the machine is disconnected from
the mains.

12.8.4 SETPOINT DETACHMENT TEMPERATURE

This parameter allows you to change the setpoint detachment temperature of the machine. By
pressing the arrows you can increase or decrease ±1ºC with each keystroke. Measured in
degrees centigrade with a 1ºC resolution.

The value can be changed with “Up/Down”. By pressing “OK”, you can store this parameter
and go to the next one. The value will remain stored even if the machine is disconnected from
the mains.

12.8.5 WATER INLET TIME

The water inlet time occurs during the set detachment time. It can be modified using the
arrow buttons and is measured in minutes and seconds with a resolution of 1 second.

Harvest time

02:00 (mm:ss)

Harvest Temp

+0ºC

«
...
49
50
51
52
53
...
»

Содержание 400 A





































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды