background image

EA-K-30 – Functions

Operating Manual

Chain actuator – EA-K-30/xxx-T(-DA)

Chain actuator

 – EA230-K-30/xxx(-S)

Page 7

BA_EA(230)-K-30-XXX_EN_12

www.simon-protec.com

Date: 13.02.2019

Issue:  1.2 / 01.2019

[email protected]

4. EA-K-30 – Functions

4.1 Soft-close   range

4.1.1 Speed reduction

The actuator has a factory-activated speed reduction 
function, the last 75 mm before reaching the “CLOSED” end 
position (see Table 1: “Electrical properties” on page 24 and 
Figure 10: “Configurable ranges” on page 8).

4.1.2 Current reduction

After reaching the last 75 mm before end position "CLOSED", 
the soft-close current becomes active, 0.3 A by default. This 
value can be increased to 1.0 A via SIMON LINK (when the 
speed reduction function is deactivated).

4.2 SIMON LINK

The actuator has a configuration interface (gear side) on 
which the following functions can be performed via SIMON 
LINK:

• The stroke can be electronically limited from 100 mm on.

• Forces can be set in the “OPEN” and “CLOSED” 

direction.

• The  soft - close  current can be adjusted.

• The speed reduction before the “CLOSED” end position 

for the soft - close  range can be set (see Figure 10: 
“Configurable ranges” on page 8).

• The switching behaviour of the dry contact can be set.

• A detailed status message from the actuator and data 

logger can be read.

Figure 9: Configuration interface for SIMON LINK

ATTENTION

In order to avoid damage to the window and actuator or 
injuries to individuals, the cut-off current limit is 
automatically reduced to 

0.3 A

 when the speed reduction 

function is activated; this corresponds to a force of 
approx. 150 N. The cut-off current limit can be increased 
to a maximum of 0.5 A (300 N) via SIMON LINK when the 
speed reduction function is activated.

INFORMATION

You need a service cable (USB-300) 
and the associated software (from 
version 2.0.0) for configuration of the 
actuator via SIMON LINK. 
For more information visit

short.simon-protec.com/slen

ATTENTION

The cut-off of the actuator in the configuration is provided 
by the USB-300 cable. 
There must be 

no

 external power supply at this point in 

time (EA-K-30/xxx-T-DA on the chain side).

gear side

connector for USB-300 cable

Содержание EA-K-30 Series





























Отзывы: