SIGNALCORE SC5309A Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 49

SIGNALCORE SC5309A Скачать руководство пользователя страница 7

Rev 2.0 | SC5309A & SC5310A

Hardware Manual

SignalCore, Inc.

6

SC5309A & SC5310A Hardware Manual

Warnings Regarding Use of SignalCore Products

(1) PRODUCTS FOR SALE BY SIGNALCORE, INCORPORATED ARE NOT DESIGNED WITH COMPONENTS NOR TESTED

FOR A LEVEL OF RELIABILITY SUITABLE FOR USE IN OR IN CONNECTION WITH SURGICAL IMPLANTS OR AS
CRITICAL COMPONENTS IN ANY LIFE SUPPORT SYSTEMS WHOSE FAILURE TO PERFORM CAN REASONABLY BE
EXPECTED TO CAUSE SIGNIFICANT INJURY TO A HUMAN.

(2) IN ANY APPLICATION, INCLUDING THE ABOVE, RELIABILITY OF OPERATION OF THE SOFTWARE PRODUCTS CAN

BE IMPAIRED BY ADVERSE FACTORS, INCLUDING BUT NOT LIMITED TO FLUCTUATIONS IN ELECTRICAL POWER
SUPPLY,  COMPUTER  HARDWARE  MALFUNCTIONS,  COMPUTER  OPERATING  SYSTEM  SOFTWARE  FITNESS,
FITNESS OF COMPILERS AND DEVELOPMENT SOFTWARE USED TO DEVELOP AN APPLICATION, INSTALLATION
ERRORS,  SOFTWARE  AND  HARDWARE  COMPATIBILITY  PROBLEMS,  MALFUNCTIONS  OR  FAILURES  OF
ELECTRONIC  MONITORING  OR  CONTROL  DEVICES,  TRANSIENT  FAILURES  OF  ELECTRONIC  SYSTEMS
(HARDWARE AND/OR SOFTWARE), UNANTICIPATED USES OR MISUSES, OR ERRORS ON THE PART OF THE USER
OR  APPLICATIONS  DESIGNER  (ADVERSE  FACTORS  SUCH  AS  THESE  ARE  HEREAFTER  COLLECTIVELY  TERMED

“SYSTEM FAILURES”). ANY APPLICATION WHERE A SYSTEM FAILURE WOULD CREATE A RISK OF HARM TO

PROPERTY  OR  PERSONS  (INCLUDING  THE  RISK  OF  BODILY  INJURY  AND  DEATH)  SHOULD  NOT  BE  SOLELY
RELIANT UPON ANY ONE COMPONENT DUE TO THE RISK OF SYSTEM FAILURE. TO AVOID DAMAGE, INJURY,
OR  DEATH,  THE  USER  OR  APPLICATION  DESIGNER  MUST  TAKE  REASONABLY  PRUDENT  STEPS  TO  PROTECT
AGAINST  SYSTEM  FAILURES,  INCLUDING  BUT  NOT  LIMITED  TO  BACK-UP  OR  SHUT  DOWN  MECHANISMS.
BECAUSE EACH END-USER SYSTEM IS CUSTOMIZED AND DIFFERS FROM SIGNALCORE'S TESTING PLATFORMS,
AND BECAUSE A USER OR APPLICATION DESIGNER MAY USE SIGNALCORE PRODUCTS IN COMBINATION WITH
OTHER  PRODUCTS  IN  A  MANNER  NOT  EVALUATED  OR  CONTEMPLATED  BY  SIGNALCORE,  THE  USER  OR
APPLICATION DESIGNER IS ULTIMATELY RESPONSIBLE FOR VERIFYING AND VALIDATING THE SUITABILITY OF
SIGNALCORE  PRODUCTS  WHENEVER  SIGNALCORE  PRODUCTS  ARE  INCORPORATED  IN  A  SYSTEM  OR
APPLICATION, INCLUDING, WITHOUT LIMITATION, THE APPROPRIATE DESIGN, PROCESS AND SAFETY LEVEL
OF SUCH SYSTEM OR APPLICATION.

«
...
5
6
7
8
9
...
»

Содержание SC5309A


















































Отзывы:

Нет отзывов