SIGNALCORE SC5309A Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 49

SIGNALCORE SC5309A Скачать руководство пользователя страница 27

Rev 2.0 | SC5309A & SC5310A

Hardware Manual

SignalCore, Inc.

26

SC5309A & SC5310A Hardware Manual

Bits

Type

Name

Width

Description

[7:0]

R

Read back byte

8

Read 1 byte back is required for PXIe
and RS232

Register 0x14 SIGNAL_PATH

This register configures how the signal chain is routed.

Bytes written 2

Bytes read 1

Bits Type Name

Width Description

[0]

W

rfPreAmp

1

0 = Turn off RF amp

1 = Turn on RF amp. This parameter is only valid
if autogain is off or autogain auto_ctrl_rf_amp is
off.

[1]

W

If2Filter

1

0 = Selects the IF2 filter #0

1 = Selects the IF2 filter #1 (custom option)

[2]

W

invertSpectrum

1

0 = Not spectral inversion

1 = IF3 spectrum inverted w.r.t RF

[3]

W

Bypass_rf_conversion

1

0 = RF is converted to IF

1 = RF is directed to the IF port (used for low
frequencies)

[7:4]

W

Not used

4

Set to zeros

[7:0]

R

Read back byte

8

Read 1 byte back is required for PXIe and RS232

Register 0x15 CONFIG_AUTO_GAIN

This register will configure the device to set the attenuator values and control the RF amplifier to
keep the device gain close to the desired gain with changes in RF frequency, as computed from its
input parameters such as RF input level, mixer level, and IF out level.

Bytes written 6

Bytes read 1

«
...
25
26
27
28
29
...
»

Содержание SC5309A


















































Отзывы:

Нет отзывов