SIGNALCORE SC5309A Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 49

SIGNALCORE SC5309A Скачать руководство пользователя страница 6

©2018

Rev 2.0

5

General Information

products. Use of SignalCore products is restricted to applications that do not infringe on the
intellectual property rights of others.

“SignalCore”, “signalcore.com”, and the phrase “preserving signal integrity” are registered

trademarks of SignalCore, Incorporated. Other product and company names mentioned herein are
trademarks or trade names of their respective companies.

International Materials Declarations

SignalCore,  Incorporated  uses  a  fully  RoHS  compliant  manufacturing  process  for  our  products.
Therefore,  SignalCore  hereby  declares  that  its  products  do  not  contain  restricted  materials  as
defined by European Union directive 2002/95/EC (EU RoHS) in any amounts higher than limits stated
in the directive. This statement assumes reliable information and data provided by our component
suppliers and may not have been independently verified through other means.  For products sold
into China,

we also comply with the “Administrative Measure on the Control of Pollution Caused by

Electronic Information Products” (China RoHS). In the current stage of this legislation, the content of

six hazardous materials must be explicitly declared. Each of those materials, and the categorical
amount present in our products, are shown below:

鉛

Lead

(Pb)

汞

Mercury

(Hg)

镉

Cadmium

(Cd)

六价

铬

Hexavalent

Chromium

(Cr(VI))

多

溴

联苯

Polybrominated

biphenyls

(PBB)

多

溴

二

苯

醚

Polybrominated

diphenyl ethers

(PBDE)

✓

✓

✓

✓

✓

✓

A

✓

indicates that the hazardous substance contained in all of the homogeneous materials for this

product is below the limit requirement in SJ/T11363-2006. An

X

indicates that the particular

hazardous substance contained in at least one of the homogeneous materials used for this product
is above the limit requirement in SJ/T11363-2006.

CE European Union EMC & Safety Compliance Declaration

The European Conformity (CE) marking is affixed to products with input of 50 - 1,000 Vac or 75 -
1,500 Vdc and/or for products which may cause or be affected by electromagnetic disturbance. The
CE marking symbolizes conformity of the product with the applicable requirements. CE compliance

is a manufacturer’s self

-declaration allowing products to circulate freely within the European Union

(EU). SignalCore products meet the essential requirements of Directives 2004/108/EC (EMC) and
2006/95/EC (product safety) and comply with the relevant standards. Standards for Measurement,
Control and Laboratory Equipment include EN 61326 and EN 55011 for EMC, and EN 61010-1 for
product safety.

«
...
4
5
6
7
8
...
»

Содержание SC5309A


















































Отзывы:

Нет отзывов