SIGNALCORE SC5309A Скачать руководство пользователя страница 5

 

Rev 2.0 | SC5309A & SC5310A 

Hardware Manual

 

 

SignalCore, Inc. 

SC5309A & SC5310A Hardware Manual 

1

 

General Information 

 

Warranty 

This product is warranted against defects in materials and workmanship for a period of three years 
from the date of shipment. SignalCore will, at its option, repair or replace equipment that proves to 
be defective during the warranty period. This warranty includes parts and labor. 
 
Before  any  equipment  will  be  accepted  for  warranty  repair  or  replacement,  a  Return  Material 
Authorization (RMA) number must be obtained from a SignalCore customer service representative 
and  clearly  marked  on  the  outside  of  the  return  package.  SignalCore  will  pay  all  shipping  costs 
relating to warranty repair or replacement. 
 
SignalCore strives to make the information in this document as accurate as possible. The document 
has  been  carefully  reviewed  for  technical  and  typographic  accuracy. If  technical  or  typographical 
errors exist, SignalCore reserves the right to make changes to subsequent editions of this document 
without prior notice to possessors of this edition. Please contact SignalCore if errors are suspected. 
In no event shall SignalCore be liable for any damages arising out of or related to this document or 
the information contained in it. 

EXCEPT AS SPECIFIED HEREIN, SIGNALCORE, INCORPORATED MAKES NO WARRANTIES, EXPRESS OR 
IMPLIED, AND SPECIFICALLY DISCLAIMS ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A 

PARTICULAR  PURPOSE.  CUSTOMER’S  RIGHT  TO  RECOVER  DAMAGES  CAUSED  BY  FAULT  OR 

NEGLIGENCE ON THE PART OF SIGNALCORE, INCORPORATED SHALL BE LIMITED TO THE AMOUNT 
THERETOFORE PAID  BY THE  CUSTOMER. SIGNALCORE,  INCORPORATED  WILL NOT  BE LIABLE  FOR 
DAMAGES  RESULTING  FROM  LOSS  OF  DATA,  PROFITS,  USE  OF  PRODUCTS,  OR  INCIDENTAL  OR 
CONSEQUENTIAL DAMAGES, EVEN IF ADVISED OF THE POSSIBILITY THEREOF. This limitation of the 
liability of SignalCore, Incorporated will apply regardless of the form of action, whether in contract 
or tort, including negligence. Any action against SignalCore, Incorporated must be brought within 
one year after the cause of action accrues. SignalCore, Incorporated shall not be liable for any delay 
in performance due to causes beyond its reasonable control. The warranty provided herein does not 

cover  damages,  defects,  malfunctions,  or  service  failures  caused  by  owner’s  failure  to  follow 
SignalCore,  Incorporated’s  installation,  operation,  or  maintenance  instructions;  owner’s 
modification of the product; owner’s abuse, misuse, or negligent acts; and power failure or surges, 

fire, flood, accident, actions of third parties, or other events outside reasonable control. 

 

Copyright & Trademarks 

Under  the  copyright  laws,  this  publication  may  not  be  reproduced  or  transmitted  in  any  form, 
electronic  or  mechanical,  including  photocopying,  recording,  storing  in  an  information  retrieval 
system,  or  translating,  in  whole  or  in  part,  without  the  prior  written  consent  of  SignalCore, 
Incorporated. 

SignalCore, Incorporated respects the intellectual property rights of others, and we ask those who 
use  our  products  to  do  the  same.  Copyright  and  other  intellectual  property  laws  protect  our 

Содержание SC5309A


















































Отзывы: