Siemens SINUMERIK 808D Скачать руководство пользователя

Страница: 55 / 270

Programming and Operating Manual (Milling)

6FC5398-4DP10-0BA1, 01/2014

See the following illustration for polar radius and polar angle with definition of the positive direction in different planes:

Pole definition, programming
G110

Pole specification relative to the setpoint position last programmed (in the plane, e.g. with G17: X/Y)

G111

; Pole specification relative to the origin of the current workpiece coordinate system (in the plane, e.g. with

G17: X/Y)

G112

; Pole specification, relative to the last valid pole; preserve plane

Note
Pole specifications

●

Pole definitions can also be performed using polar coordinates. This makes sense if a pole already exists.

●

If no pole is defined, the origin of the current workpiece coordinate system will act as the pole.

Programming example

N10 G17

; X/Y plane

N20 G0 X0 Y0

N30 G111 X20 Y10

; Pole coordinates in the current workpiece coordinate system

N40 G1 RP=50 AP=30 F1000

N50 G110 X-10 Y20

N60 G1 RP=30 AP=45 F1000

N70 G112 X40 Y20

; New pole, relative to the last pole as a polar coordinate

N80 G1 RP=30 AP=135

; Polar coordinate

M30

Traversing with polar coordinates
The positions programmed using polar coordinates can also be traversed as positions specified with Cartesian coordinates

as follows:

●

G0 - linear interpolation with rapid traverse

●

G1 - linear interpolation with feedrate

●

G2 - circular interpolation CW

●

G3 - circular interpolation CCW

(See also Sections "Linear interpolation (Page 69)" and "Circular interpolation (Page 72)".)

Содержание SINUMERIK 808D















































































































































































































































































Результаты поиска

Содержание SINUMERIK 808D

Отзывы:

Похожие инструкции для SINUMERIK 808D

Бренды по названию

Популярные бренды

Siemens SINUMERIK 808D, Руководство по программированию и эксплуатации

Результаты поиска

Содержание SINUMERIK 808D

Отзывы:

Похожие инструкции для SINUMERIK 808D

Бренды по названию

Популярные бренды