Siemens SIMATIC RF1000 Series Скачать руководство пользователя страница 64

Страница: 64 / 77

The demo application

7.2 Creating a custom application

SIMATIC RF1000

Operating Instructions, 02/2020, C79000-G8976-C432-07

Own application "Transfer reader configuration"

Requirement: A corresponding VHL configuration was created and transferred to a

configuration card.
Follow the steps below to transfer a reader configuration using a configuration card:
1.

Establish the connection to the reader ("brp_open_usb_session" or

"brp_open_serial_session").

Check whether a configuration card is located in the read range of the reader

("vhl_select"; "AllowConfig = true").
If a configuration card is located in the read range, the status code "CONFIG_READ" or

"HF_ERR" is returned and the configuration is transferred to the reader. Parameterization

is complete as soon as "vhl_select = STATUS_OK" is returned.

Terminate the connection to the reader ("brp_close_session").

Establish the connection to the reader again ("brp_open_usb_session").

The source code of the demo application can serve as an example for your own application.

Figure 7-5

"Transfer reader configuration" flow diagram

Содержание SIMATIC RF1000 Series














































































Результаты поиска

Содержание SIMATIC RF1000 Series

Отзывы:

Похожие инструкции для SIMATIC RF1000 Series

Бренды по названию

Популярные бренды

Siemens SIMATIC RF1000 Series, Руководство по эксплуатации

Результаты поиска

Содержание SIMATIC RF1000 Series

Отзывы:

Похожие инструкции для SIMATIC RF1000 Series

Бренды по названию

Популярные бренды