Siemens SIMATIC RF1000 Series Скачать руководство пользователя страница 41

Страница: 41 / 77

Programming

6.3 Programming via the RS232 interface (using the Freeport protocol)

SIMATIC RF1000
Operating Instructions, 02/2020, C79000-G8976-C432-07

6.2.2

Functions of the USB interface for Linux

The programming in Linux is made via an API and Software Development Kit. For additional

information, contact the Siemens Industry Online Support (Page 77).
Alternatively, you can program the USB interface in Linux based on the serial telegrams.

These are described in section "Programming via the RS232 interface (using the Freeport

protocol) (Page 41)".

6.3

Programming via the RS232 interface (using the Freeport protocol)

When the RF1040R/RF1070R readers are connected to a SIMATIC controller or any serial

interface, communication is performed via the Freeport protocol. The freeport protocol allows

you to communicate with the reader directly on the lowest level. A USB connection is not

required for this.
The telegrams are listed in a byte coding in the following sections; you can apply the byte

coding directly to the user program of the controller.
The communication parameters of the RS232 interface of the reader are set as follows in the

factory:

●

Data bits: 8

●

Parity: None

●

Stop bits: 1

●

Transmission speed: 115.2 kBd

Connection via a communications module or serial module
The reader can be connected to a SIMATIC controller using a SIMATIC Ident communication

module with RS232 interface. With a connection via the CM, you need to set the

communication parameters of the CM as follows:

Table 6- 20 Setting options in the "Module parameters" parameter group of the CM when using the

freeport protocol

Parameter

Parameter value

Description

User mode

Ident profile/RFID stand-

ard profile
FB 45 / FC 45

Selection of the block with which you want to

assign parameters to the reader.

MOBY mode

Freeport protocol

The parameter value "Freeport protocol" must

be selected in this parameter.

Transmission

speed

115.2 kBd

The parameter value "115.2 kBd" must be se-

lected in this parameter.

Diagnostic

messages

None
Hard errors

Selection of whether hardware diagnostics mes-

sages are reported.

Содержание SIMATIC RF1000 Series














































































Результаты поиска

Содержание SIMATIC RF1000 Series

Отзывы:

Похожие инструкции для SIMATIC RF1000 Series

Бренды по названию

Популярные бренды

Siemens SIMATIC RF1000 Series, Руководство по эксплуатации

Результаты поиска

Содержание SIMATIC RF1000 Series

Отзывы:

Похожие инструкции для SIMATIC RF1000 Series

Бренды по названию

Популярные бренды