Siemens SIMATIC RF1000 Series Скачать руководство пользователя страница 56

Страница: 56 / 77

Programming

6.4 Status codes

SIMATIC RF1000

Operating Instructions, 02/2020, C79000-G8976-C432-07

The functions are constructed so that if execution fails, they are automatically repeated. This

compensates any communications problems that may occur, e.g. due to bad RF signal

quality as a result of external influences.

Table 6- 50 RS232-specific status codes

Value Variable

Description

0x00 OK

No error

0x40 CMD_WORK

The job is currently being processed.

0x41 INVAILD_CMD_ERR

Invalid function
Causes:

•

The function is not valid.

•

The parameters are invalid.

•

The response exceeds 255 bytes.

•

Missing configuration

0x42 ACCESS_DENIED_ERR

Missing authentication

0x81 TIMEOUT_ERR

The reader is currently in timeout.

0x82 FRAME_ERR

Invalid command from host.

0x83 AME_OVERFLOW_ERR

The length of the response exceeds the maximum per-

missible length.

0x84 CHK_ERR

Invalid checksum in the host command.

Содержание SIMATIC RF1000 Series














































































Результаты поиска

Содержание SIMATIC RF1000 Series

Отзывы:

Похожие инструкции для SIMATIC RF1000 Series

Бренды по названию

Популярные бренды

Siemens SIMATIC RF1000 Series, Руководство по эксплуатации

Результаты поиска

Содержание SIMATIC RF1000 Series

Отзывы:

Похожие инструкции для SIMATIC RF1000 Series

Бренды по названию

Популярные бренды