Siemens SIMATIC RF1000 Series Скачать руководство пользователя страница 55

Страница: 55 / 77

Programming

6.4 Status codes

SIMATIC RF1000
Operating Instructions, 02/2020, C79000-G8976-C432-07

6.4

Status codes

The following table contains a list of the status codes of the VHL command set divided up

into command groups.

Table 6- 49 General status codes

Value

Variable

Description

USB

RS232

syscmd
0x0000 0x00

STATUS_OK

No error

vhl
0x0101 0x01

NOTAG_ERR

Transponder does not exist or no response.
This status code requires reselection of the

card with the function "vhl_select".

0x0102 0x02

CARD_NOT_SELECTED_ERR The function cannot be executed because

no transponder is selected.

0x0103 0x03

HF_ERR

Communications problems with the tran-

sponder.

0x0104 0x04

CONFIG_ERR

The structure of the VHL function is invalid

or was not found.

0x0105 0x05

AUTH_ERR

Authentication error. The keys in the VHL

function are invalid (MIFARE) or the stamp

in the reader is invalid (LEGIC cards).

0x0106 0x06

READ_ERR

The communications sequence is success-

ful, but reading failed.

0x0107 0x07

WRITE_ERR

This value is currently not supported.

0x0108 0x08

CONFCARD_READ

A transponder was recognized.

0x0109 0x09

INVALID_CARD_FAMILY_ERR The required transponder type does not

match the transponder family of the current-

ly selected transponder.

0x010A 0x0A

NOT_SUPPORTED_ERR

The function is not supported.

0x010B 0x0B

VHL_FORMAT_ERR

Format error

0x010C 0x0C

VHL_HW_ERR

Hardware problems during access (e.g. on

the reader chip)

Autoread
0x0501 0x01

NO_MESSAGE_ERR

No valid card / no valid transponder recog-

nized.

0x0502 0x02

SCRIPT_RUNTIME_ERR

Runtime error detected during script execu-

tion.

0x0503 0x03

SCRIPT_SYNTAX_ERR

Syntax error in the script

0x0504 0x04

SCRIPT_NOT_IMPL_ERR

Scripts does not exist.

0x0510 0x10

AR_DISABLED_ERR

"Autoread" function is switched off.

Содержание SIMATIC RF1000 Series














































































Результаты поиска

Содержание SIMATIC RF1000 Series

Отзывы:

Похожие инструкции для SIMATIC RF1000 Series

Бренды по названию

Популярные бренды

Siemens SIMATIC RF1000 Series, Руководство по эксплуатации

Результаты поиска

Содержание SIMATIC RF1000 Series

Отзывы:

Похожие инструкции для SIMATIC RF1000 Series

Бренды по названию

Популярные бренды