Siemens SIMATIC HMI TP1000F Mobile RO Скачать руководство пользователя страница 68

Страница: 68 / 196

Handling the Mobile Panel

4.3 Pressing the emergency stop / stop button

TP1000F Mobile RO

Operating Instructions, 08/2017, A5E39831415-AA

4.3

Pressing the emergency stop / stop button

The emergency stop / stop button on the HMI device is an optional operator control. The

emergency stop / stop button is designed with two circuits and enables a safety-related

emergency stop or stop of the fail-safe automation system.

Note

•

Whether the emergency stop / stop button has the "emergency stop" or "stop" function

depends on the configuration of the plant and the parameter settings of the HMI device.

•

If the emergency stop / stop button is configured and wired for the "emergency stop"

function, the emergency stop / stop button lights up as soon as the "emergency stop"

function becomes available.

•

An emergency stop or stop can only be triggered when the fail-safe HMI device is

attached to a connection box.

For a hardwired F-system:

●

When a SIRIUS safety relay is used, the emergency stop / stop button meets the

requirements of Safety Category 3 in accordance with EN ISO 13849--1.

●

When you unplug the connecting cable from the connection box, the emergency stop

circuit is either opened or automatically bypassed, depending on the connection box

used.

Requirement

●

The HMI device is connected to a correctly installed connection box.

Содержание SIMATIC HMI TP1000F Mobile RO





































































































































































































Результаты поиска

Содержание SIMATIC HMI TP1000F Mobile RO

Отзывы:

Siemens SIMATIC HMI TP1000F Mobile RO, Руководство по эксплуатации, Страница: 68 / 196

Результаты поиска

Содержание SIMATIC HMI TP1000F Mobile RO

Отзывы: