manualshive.com logo in svg

Siemens SIMATIC HMI TP1000F Mobile RO, Руководство по эксплуатации, Страница: 65 / 196

Поделиться
Скачать
Siemens SIMATIC HMI TP1000F Mobile RO Скачать руководство пользователя страница 65

 

TP1000F Mobile RO 
Operating Instructions, 08/2017, A5E39831415-AA  

65

 

 

Handling the Mobile Panel 

4 

4.1

 

Holding the Mobile Panel and attaching it to the wall-mounting 

bracket 

Holding the HMI device 

The figure below shows the device being held on the forearm. 

 

When holding the Mobile Panel as shown, you can, for example, perform movements in the 

fail-safe automation system during setup mode.  
The HMI device is easy to operate when held on the forearm as shown. With your free hand, 

you can reach the front of the device and the emergency stop / stop button. You can activate 

the enabling button with the hand holding the HMI device. The enabling button is optimally 

accessible.  

 

 

NOTICE 
Holding the HMI device during setup mode 
Potentially dangerous movements can be controlled manually if setup mode is activated. 
To ensure that the emergency stop / stop button and enabling button can be operated 

quickly in a dangerous situation, the HMI device must be held on your forearm as shown. 

 

If you are only entering data and are not controlling potentially dangerous movements, you 

can hold the HMI device with both hands on the left and right instead of on your forearm. 

Содержание SIMATIC HMI TP1000F Mobile RO





































































































































































































Отзывы:

Нет отзывов