Siemens SIMATIC HMI TP1000F Mobile RO Скачать руководство пользователя страница 67 | Manualshive

Страница: 67 / 196

Siemens SIMATIC HMI TP1000F Mobile RO Скачать руководство пользователя страница 67

Handling the Mobile Panel

4.2 Operating the enabling button

TP1000F Mobile RO
Operating Instructions, 08/2017, A5E39831415-AA

67

4.2

Operating the enabling button

The enabling mechanism comprises one integrated enabling button with three settings.
The signals of the enabling button are evaluated internally and sent to the connection box

over the connecting cable. For setup mode, these signals must be wired dual-channel from

the connection box to the F-system.

Requirement

●

The HMI device is connected to a correctly installed connection box.

Procedure

1.

Press the enabling key to switch position 2 or 3.

Switch position

Function

Enabling button switch status

1

Neutral position

Opened

2

Enable

Closed

3

Panic

Opened

–

The figure below shows the switching sequence for normal operation.

–

The figure below shows the switching sequence for panic operation.

2.

Release the enabling button.
If the enabling button is in switch position "3", the "Enable" setting is skipped when the

button is released.

Note
Releasing the enabling button and the "Panic" switch position do not require

acknowledgement of the safety shutdown.

«
...
65
66
67
68
69
...
»

Содержание SIMATIC HMI TP1000F Mobile RO





































































































































































































Отзывы:

Нет отзывов