Siemens SICAM Q80 Скачать руководство пользователя страница 55 | Manualshive

Страница: 55 / 240

Siemens SICAM Q80 Скачать руководство пользователя страница 55

55

Operation modes and settings

Power Quality Recorder SICAM Q80 7KG8080, System manual

E50417-H1076-C420-A2, Release 12.01.2015

5.1.2.3.6 Output SICAM Q80 7KG8080

Pre-defined functions can be assigned to the digital outputs. By this means, for example, a variety of measurement
states can be signalled by external display elements.

The digital outputs are designed as relay contacts: If a bit's value is 1, the switch is closed. The connected voltage
must be supplied from outside. There is no internal connectable voltage (TTL etc.)

Clicking in the function column of a binary output opens a list of available functions:

Digital outputs; load default settings by button "Set Default"

LED – shines green when the relay is closed.

Name of DO anything except / \ : * ? < > |

For cutoff values, values can either be defined or parameters of the selected standard can be used.

Function

Description

System fault / device active

Only at DO1: The closed relay contact (LED=green) indicates that the device is
measuring. If the relay fails during measurement (LED=red), then there is either an
error in calculation of the data, or the measurement has been concluded correctly.

Voltage dip

The relay closes when the RMS voltage value falls below the

cutoff value for event

.

Low free storage

The relay closes when the free data storage falls below a cutoff limit. The cutoff
limit is specified in MBytes.

Unbalance

The relay closes when the asymmetry exceeds a

.

No synchronization signal

The relay closes when the synchronization signal is no longer available.

RMS trigger U

The relay closes when the RMS voltage value deviates according to the settings in
the

(No. 5).

RMS trigger I

The relay closes when the RMS voltage value deviates according to the settings in
the

(No. 8).

Frequency trigger

The relay closes if the frequency deviates according to the settings in the

(No. 9).

THD U

The relay closes when defined for THD occurs.

Harmonics U

The relay closes when an

defined for the harmonics occurs.

Active Overall system

The relay closes when an

defined for the overall system's power occurs.

Reactive Overall system

Apparent Overall system

Power factor Overall system

The relay closes when an

defined for the overall system power factor

occurs.

Active line

The relay closes when an

defined for a line power value occurs.

Reactive line

Apparent line

Power factor line

The relay closes when an

defined for a power-power factor occurs.

47

47

42

42

42

47

47

47

47

47

«
...
53
54
55
56
57
...
»

Содержание SICAM Q80

















































































































































































































































Отзывы:

Нет отзывов