Siemens SICAM Q80 Скачать руководство пользователя страница 158 | Manualshive

Страница: 158 / 240

Siemens SICAM Q80 Скачать руководство пользователя страница 158

158

SICAM Q80 7KG8080

Power Quality Recorder SICAM Q80 7KG8080, System manual

E50417-H1076-C420-A2, Release 12.01.2015

6.3.2

View menu

View menu

Toolbar, Status bar:

Shows/hides these two interface elements.

Tile

: Shifts the dividing border between the tree diagram and the editor. It's also

possible to move the line directly by clicking it with the mouse and moving the
mouse with its button held down.

Load/Save page contents (as):

In some formulas, the content displayed (e.g. value

limits) can be saved independently of the measurement task

Curve window navigation:

Opens the toolbox, see Section

.

Delete curve window:

See Section

Working with the curve window

.

Data representation:

Affects the active window, e.g. by clicking in the curve window.

Line: Default representation, samples are connected by straight lines

Bar graph: Each sample is represented by a bar, suitable for
histograms

Table: Tabular representation of samples, suitable for events

Bar (Histograms): Each sample is a bar and the x-unit is adapted for
histograms.

Time representation:

Time axis with relative or absolute time. Affects active curve

window.

6.3.3

Evaluation menu

Evaluation menu

To analysis:

Goes to the start page for data analysis

Histogram, (1-) Cumulative frequency,

see Section

Working with the curve

.

Previous/Next curve view:

Moves to a different screen; see

Working with the

Delete measurement data:

Deletes result data sets produced by the analysis.

The data to be recorded are not affected. Either the currently displayed
measurement or all evaluation results generated thus far can be deleted.

Delete measurement data:

Deletes temporary calculations and closes the measurement data sets which are open. In the process, recorded
data are not deleted, but the currently displayed measurement or all evaluation results generated to date can be
deleted. If the data evaluation is very elaborate, the large amount of measured data open can cause slowing of the
PC's operation, so deleting and closing some data can be a remedy.

Export data:

Evaluated measured data can be exported
either in Excel format or as text files. The
condition for Excel export is installation of
Microsoft Excel.

Descriptions of the format templates for

and

are presented further below.

199

186

186

186

167

159

«
...
156
157
158
159
160
...
»

Содержание SICAM Q80

















































































































































































































































Отзывы:

Нет отзывов